how to clean ender 3 v2 bed 3d models

a knob for the drawer if you want to change the color

I provide the source you can edit according to your needs

An inexpensive timelapse rig intended to work with a headphone button and a smartphone

Easy to print gear without the need for distribution after printing

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Bltouch support. ... Just fixed by the 2 small holes on the plate. No disassembly to do. I redesigned it because the one I had downloaded put the sensor too low compared to the nozzle.I moved it up 3mm.

Two files. ...One is a short snip that you can extend to fit your needs. The other is for the Y rails with a cutout to fit all the way into the uprights flush against back.

... The gantry has to be taken off to install the pin into the bracket. Suggested layer height: Wheel - 0.125mm Bracket & Pin - 0.2mm NOTE: If you can't get it to fit together, you can try setting "slicing tolerance" to "exclusive" in your slicer :)

Feeder guide to minimize abrasion of the brass feeder hole. ... open the two screws that hold the feeder assembly in place, slot it in and you should be good to go. ...replace when it runs down.

I remixed this mount to fit microswiss hotend better. I have china copy microswiss what measured 1.4mm shorter than creality stock hotend. Use m3 screws to fit it. ... Thats my first post in thingiverse Sorry my poor english

A simple filament guide to keep it from touching the Z axis. Thank you for all the support.

EDIT - 08-13-21 Revised my model a bit to be more stable and also changed the angle that spool enters the guide to make extrusion cleaner. Loved the original design idea but I have changed to a metal extruder from Creality on my machine so the guide...

The supports may wrap around the handle, but it just takes some time to take it off.

... it in place or do what I did and use a couple thin strings of blue sticky tack along the bottom of the flat outer frame. I purposely designed it to have a slight bit of wiggle room (<0.2mm) so you should not have to make any post-print adjustments.

Modified the original design to accept a normal webcam. ...Print as described as in the original post.

EDIT - 08-13-21 Revised my model a bit to be more stable and also changed the angle that spool enters the guide to make extrusion cleaner. Loved the original design idea but I have changed to a metal extruder from Creality on my machine so the guide...

Print the flat side down, 0 bottom layers and set your infill parameters to have a nice looking mesh.

Wanted something fun for the riser feet on my machine so I remixed this Grumpy Dino to fit. ...From the bottom of the Dino to the bottom of the machine is 52mm and then I added some adhesive rubber to the bottom for vibration damping.

... screw for the Z axis. ... You might want to remove the axis completely, to avoid losing the small lock nuts between the guide and the support. ... Might be a little difficult to install, because of the alignment of the holes but the result is worth it.

I made it stick out farther because I use a HatchBox filament on a larger roll so the original was too close to the printer. I added holes to reduce the amount of filament used. I also made a support column. ...It will hold the spool just fine...

You may need to cut them a bit varying form side to side, there a some screws blocking the T-rail. A cheap solution compared the typical used squash-balls. I use it a few mouths now and I am totally happy with them. ...The two parts need to be glued...

Rail insert to facilitate future creations without wasting time trying to find the best fit. Make sure the printer is properly calibrated as the fit is very tight. Use brim for best result. The files have the STL version and also the version...

... note that the drawer knob is not fully tested, as I glued it on instead of clicking it in. To do the latter, you probably need to print it horizontally. ... I've added the original blend file for those who might want to tinker a bit with the design.

Remix of https://www.thingiverse.com/thing:4596763 I made the glue holder wider to fit the larger Elmer glue stick

Please don't hesitate to share it as a makeWould recommend slicing yourself since i have made a few updates on the model

Found this on Reddit, after hours of looking for it. ...Did not drawing them just wanted to share them with everyone.

After replacing the X and the Y axis tensioners I thought it would be nice to have a complement design for the screen rotary knob..