how to change filament ender 3 v2 3d models

Printed in PLA , 0.8mm top, bottom and walls, with 10% Gyroid infill Remixed with Ender tool holder slide-in-rail clip , flipped over to print flat and resized to 110mm away from gantry. NB works well, but slide in clip could do with some resizing...

That way if you mount your material up top it should still work for you, I prefer to have my material on rollers to the side of my printer. Please tell me how it works for you or if you have any suggestions for improvements! ... sensor: ...

Just a little roll for to put between the original holder and the filament spool, so it doesnt wiggle arround that much while printing.

https://www.thingiverse.com/thing:4735175 Did not fit on my Ender 3v2 machine because there was a metal plate on the "bottom" of the X stepper preventing a decent mount. I made the sleeves that grab the axis longer to make it fit. ... The pulley...

... extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this. ... Just over an hour to print and about 5minutes to install, with very little filament usage.

... at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this. ... Just over an hour to print and about 5minutes to install, with very little filament usage. ...

3cm longer version of the filament feeder to better fit with the https://www.thingiverse.com/thing:4683505 In the original version, the filament goes at a very sharp angle in two places and doesn't come back on the spool for me.

... bearings to reduce drag and friction. Easily fitted with no tools and attached to the extrusion in the frame. I will add a shorter and slightly longer roller in the future. The medium one here seems to work with all the filament spools I have.

... bearings to reduce drag and friction. Easily fitted with no tools and attached to the extrusion in the frame. I will add a shorter and slightly longer roller in the future. The medium one here seems to work with all the filament spools I have.

This will stop your filament touching the greasy Z Screw Rod, and also if you run it like I do from my Sunlu filament holder it reduces air and moisture getting to the filament Print to your usual settings for any small print, any material will...

... au centre et ne touche pas le bord du levier. J'ai aussi intégré un support de câbles. With this filament guide you will be able to print these great objects: https://www.thingiverse.com/thing:4853538 or https://www.thingiverse.com/thing:5004757

... au centre et ne touche pas le bord du levier. J'ai aussi intégré un support de câbles. With this filament guide you will be able to print these great objects: https://www.thingiverse.com/thing:4853538 or https://www.thingiverse.com/thing:5004757

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

I've seem similar roller guides but I wanted to design one that will let me remove the filament from the roller without having to unload the filament from the hotend. This allows me to remove the roller while loading the filament if it's giving me...

I wanted a simple guide to keep the filament running into the extruder at a better angle and the ones I had seen were a bit too much work for what I wanted (I personally prefer fewer moving parts), so I designed this.Just over an hour to print and...

This is a simple filament guide I made because I did not like that the filament would rub against the Z-Axis Guide Rod when printing. To mount, all you do is remove the 2 screws beside the guide rod and slide the piece over. Once done, reinstall the...

This filament guide holds the filament out from the printer 100mm and pushes it back about 50mm

... for better support on the printer so that the clip doesn't keep falling down from the pressure of the filament as it is fed through during printing. ...I use a little piece of tape to hold the extended block to the printer upright and it works great.

... Supports are recommended/necessary in my opinion. Great filament guide if you have a side spool holder. Don't forget to print the 2 spacers and sleeve for the 608 bearing this mount uses, those pieces are found on the original post I remixed from!

I personally haven't tested the thin version, but i think it should be plenty strong enough to hold the filament roll. The thick one is shown in the pictures To install, just line up and push it in. It uses the rails to align/hold it in place. I am...

Based on idea from: https://www.thingiverse.com/thing:2885049 Remixed between this https://www.thingiverse.com/thing:2873157 and this https://www.thingiverse.com/thing:2147179 I currently use Filament sensor simplified, please refer to this video for...

Filament guide and dust filter for Creality standard and upgraded extruder.

I used a mini micro switch. ...The filament enters the extruder completely straight.

Filament guide. ...Requires the removal and install off 2 screws on the extruder.

This is designed to be as similar as possible to the stock filament holder, but uses bearings to fix issues with spool gripping on the shaft. Uses two 1/2 (ID) x 1 1/8 (OD) x 5/16 (W) ball bearings (I used...

Just another filament guide. slip on, so no need for any tools or bearings. ...print without support, and put in place

If you want you can use the design without the bowden tubes as well but I have couple of connectors lying around so I wanted to use them and it also look cooler. The coolest part is it does not need any supports(I really hate printing and removing...

If you want you can use the design without the bowden tubes as well but I have couple of connectors lying around so I wanted to use them and it also look cooler. The coolest part is it does not need any supports(I really hate printing and removing...

I printed below(2917932), but the base is not so solid and weak(too short), so I remix it with other designs (4570426 & 4823360) Filament Guide_Guide_Open and Filament Guide_Guide_Flat are from 2917932. ... https://www.thingiverse.com/thing:2917932 ...

This is a spacer that prevents the filament from touching the greasy z-axis screw. ... It requires a minimal amount of plastic and can be fitted without any additional screws.