how to change filament ender 3 v2 3d models

A precisely fitted 4mm flat keyed shaft, perfectly suited to its application.

... that PETF tube guide was blocking access for the crew. Since the holes were just large enough to fit a screw head, I decided to shrink them down to 4.1 mm in size. ...This modification allows the guide to be securely bolted onto the extruder.

Slightly taller height in order to match the height of the extruder

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

Thanks to this model, you will be able to both filter the dirt in your filament and position the filament sensor and follow the filament. Any support setting can be used. ...I printed with linear support

I made a flippable screen cover for the Ender 3 V2 screen since I haven't seen any designs like this so I created my own. I designed a screen cover that uses a hinge system allowing users to open and close it whenever needed. The main purpose was to...

... essential to fine-tune your tolerances. In my case, I had to boost my horizontal expansion by .1mm in Cura for the roller to function properly. ...Additionally, using a washer between the bearing and the body piece helped ensure smooth movement.

Designed to set on top of the display on either the ender 3 v2 or ender 3 s1 (which has the same screen). ...Helps keep the screen dust free and is very helpful for blocking the light at night.Print Instructions: Print flat with supports for the over...

... I cut off this particular fragment prior to assembly. Additionally, I designed holes in the roller to accommodate two extra countersunk screws (also M4x15) for added reinforcement of the bearing section, given my tendency to drop items on occasion.

... on. Now, I'm having some doubts about whether my custom clip will fit the original files - I designed it to be compatible, but during testing, it turned out to be just a bit too snug. ...Maybe scaling up the design slightly could be the solution!

... to attach the bearings to the shaft. For the roller, you can choose either to glue it directly or use rubber bands to keep everything removable. ...Four rubber bands are sufficient, but when you have a stash of them, it's easy to get carried away!

I had a twin Z axis installed so didn't want to disassemble it to fit thr original so just cut a notch out. ... It will go around the Z thread and fit on as intended.

... perfectly. To install the hub, you need to trim the shoulder of the original support. This will allow for a secure connection. ... The end insert must be bonded to the support using a suitable adhesive, such as chloroform for PLA materials.

... ...After printing the piece I have realized that PETF tube guide was obstructing access to the crews. As the holes were the size of screw head, I have also reduced the size of that holes down to 4,1 mm, so now the guide can be bolted to the extruder.

... which was prone to snapping off during use. ...To prevent this, I reinforced it for added durability. I also opted for a 100% infill print, but in reality, you might be able to get by with a lower percentage and still achieve satisfactory results.

... existing draw handle no need for glue or anything like that as its a nice strong fit. please let me know if it works and if you like it. I printed this on a ender 3 v2 - bed temp 60 - nozzle temp 190 ( please link to original post if remixed )

Designed one that slides onto the frame itself (then realized someone had already made this, but fun to make anyway!) Not sure if my clip will fit the original files; I designed it to fit but it was a bit too tight in my testing. ...A small scale up...

Designed one that slides onto the frame itself (then realized someone had already made this, but fun to make anyway!) Not sure if my clip will fit the original files; I designed it to fit but it was a bit too tight in my testing. ...A small scale up...

Designed one that slides onto the frame itself (then realized someone had already made this, but fun to make anyway!) Not sure if my clip will fit the original files; I designed it to fit but it was a bit too tight in my testing. A small scale up...

This is a remix of https://www.thingiverse.com/thing:3098332 Added strong screw supports and also holes for the upper screws to be fixed from inside.

In my picture it shows two unused holes on top, I figured out they are too close to the other ones on the same corner. So I covered them but I could post one with them uncovered if anyone wants it. The tough ones to tighten are on the bottom! I...

I was messing around in Solidworks, and I managed to come up with something pretty interesting. ...Printing it might not be a straightforward process though.

This is 100% the original part, I just removed the text and the arrow to remove unnecessary print time and complexity :) Category: 3D Printer Accessories

Based on https://www.thingiverse.com/thing:2873157, an angle adapted to a spool holder is found at https://www.thingiverse.com/thing:2948891.

The Human is standing at a height of 104 millimeters. ... Supportive structures are indeed provided. The infill density falls within the range of thirty to fifty percent.

... support and (hopefully) a more stable base to print vertically. I still opted for a small brim to further prevent the printing moving / breaking off the bed if knocked during printing. ... Remixed from: https://www.thingiverse.com/thing:3209211

I've upgraded my th3d sensor to version 2, adding a vital new feature: two mounting holes instead of one. To secure it firmly in place, I employed two robust M3 x 12 screws paired with sturdy t-slot nuts on the frame. ...Additionally, I used two longer...

A remake of many similar sensors out there, suitable to sensors available locally.  Included are models of the bearing and limit switches used.  DO NOT PRINT THESE.  Or do, up to you, but they're not needed for the sensor. ...;-)I've included them for...

I simply shortened it a bit and strengthened it to keep it from breaking. I printed at 100% infill just to keep it strong, I'm sure you could get away with much less. Print instructionsCategory: 3D Printer Accessories Summary This is a remix. I found...