hoverboard charging port cover 3d models

I purchased a Chinese two-wheeled hoverboard and noticed that it lacked protection for the charging port from dust and moisture. I designed a plug using Tinkercad to address this issue. The printed part in PLA on my machine was loose, so I wrapped...

... in my remix no support needed 2 - the little tongue of the piece is longer .. it'll keep the piece to fit better i post also one picture with the cover plugged / unplugged so you can see the way it should be mounted ! ... I printed it in Tpu

... in my remix no support needed 2 - the little tongue of the piece is longer .. it'll keep the piece to fit better i post also one picture with the cover plugged / unplugged so you can see the way it should be mounted ! ... I printed it in Tpu

... the battery case. 2 are under pressed in guide pins ( see the picture). The screw and spring worked well with the cover I designed.I printed the cover using:PLA+100% infill (it's a small part)This cover is probably the same on other charging ports.

... the battery case. 2 are under pressed in guide pins ( see the picture). The screw and spring worked well with the cover I designed.I printed the cover using:PLA+100% infill (it's a small part)This cover is probably the same on other charging ports.

I designed a straightforward charging port cover for my Onewheel Pint. I printed it with Flexi PLA at a layer height of 0.3mm, and it only took under ten minutes to print. If you want an even tighter fit, feel free to enlarge the design by 1-2%. ...No...

I made this charging port cover for my ebike because the original one broke.You can print this cover with TPU. Ideally, you print it with the bolt symbol facing down. ...If you want to avoid the overhang, there is a version without the bolt.</p><p>The...

... It isn't intended for frequent use, as it's meant for individuals who remove their battery from the frame to charge it. I've tested this model, and the battery still slides out smoothly. I don't grant anyone else permission to sell these designs.

It is for people who take their battery out of the frame to charge it. I have tested it and the battery is still able to slide out. I do not give anyone else permission to sell these. You have permission to print one for yourself or a friend. ...Please...

Charging port cover, e.g. ...for the Xiaomi Mi Electric Scooter (M365, 1S or Pro 2) to protect charging port against splash water.

Created this due to the rubber ports breaking off of my DJI Inspire 2 Controller charging ports. ...These covers help keep dust and dirt out of the charging ports while in use or in storage.

3D printable charging port cover replacement for Denver Orus / Carrefour Toplife ebike. ...Working great on an Orus E4000.

This is a redesigned charging port cover for Bulls e-bike. ... I re-designed it because the original one was prone to be lost Bosch Battery Gen 4

The Orus E4000 Ebike Charging Port Cover Replacement is a Game Changer. Easily Printed and Installed, this Customized Part Ensures a Secure Fit and Smooth Operation of the Denver Orus / Carrefour Toplife Ebike's Charging Port. ...Perfect for DIY...

If the rubber charging port cover on the bottom of your Radiomaster Zorro doesn't stay closed, this simple clip will keep it closed. Note that it uses the rear slots for the 18650 battery holder. ... If you're strapping anything to the bottom of the...

This replacement cap protects the charging port of your Razor Pocket Mod. ...A small tab has been added for convenient removal.

Designed for the charging connector on the KOOWHEEL D3Mini ( FB1 ), this adapter should also fit other electric skateboards with a 5mm diameter charger! I recommend printing at least two pieces to ensure a secure connection. ...The original design has a...

Designed for the charging connector on KOOWHEEL D3Mini (FB1), this adapter should also fit other electric skateboards with a charging connector that's exactly 5 millimeters in diameter. I recommend printing at least two pieces. ...The original design...

This carport design doubles up as an electric charging station for eco-friendly vehicles in the future. We value your input, so feel free to share any thoughts or suggestions. ...Kindly like the post before downloading to support us financially.

For Xiaomi Yi camera - http://goo.gl/1zrPejThis ports cover was done to protect sd cart and HDMI port while allowing micro usb charger connection.That way you could additionally power Yi from power bank etc.Category: Camera Thank you for your...

... ... This protective case for the SD card slot and HDMI port is designed to safeguard your device while still allowing for a convenient micro USB charger connection. ...This way, you can also power up your Yi from a power bank or other external source.

This is a replacement cover for the Batavus Fuego E-Go 7s charging port. It probably will fit other models, because their original design was once again so flimsy and crappy, that they probably used it on many other models to save even more...

This is a replacement cover for the Batavus Fuego E-Go 7s charging port.It probably will fit other models, because their original design was once again so flimsy and crappy, that they probably used it on many other models to save even more money.As...

Installed on the Garmin Fenix 5 charging port, it is easy to remove when your watch needs to be recharged. ... Compatibility： Fenix 6/6 Pro/6 Sapphire Fenix 6s/6s Pro/6s Sapphire Fenix 6x/6x Sapphire/6x Pro Solar Fenix 5s/5s Plus Fenix 5/5 Plus ...

This cover remains in place both while charging and when the charge port door is securely closed. The Mennekes plug prevents it from being accidentally removed during charging. It's best to print this cover using a flexible material like nylon (PA)....

My Feline Friend Destroyed the Charging Port Covers on Both of My Roomba's. I've Decided to Create a New One Using Flexible Filament. I Chose TPU, Which Worked Out Great for This Project. There Are Two Different Models Available - One for the Roomba...

- use cooling - print in tpu - adjust flow +/- 2-5% if it is too loose or tight

Designed for Xiaomi M365 electric scooter.

I add a small rectangle, in order to make it easier to extract from the connector with your fingers. ... All the credits for the original part to the creator: https://www.thingiverse.com/thing:4752527

- print in flexible - cooling is a must - subtract or add 2-5% of flow if it is too tight or too loose