hotas desk mount 3d models

Inspired by http://www.thingiverse.com/thing:1370241 by gpvillamil, I designed a mount to keep the eero's default orientation but suspend it from under a desk. Note that the material in your desk may cause interference. ...The eero blog says "Keep your...

Designed a mount to hold a Dell D6000 dock to the bottom of a desk. It is designed to slide in from the back with a clip built in to add friction to hold it in place. The holes are setup for #8 pan head screws. Features: Tool-less install/removal of...

The USB ports face upwards or downwards, depending on how you mount it, and the buttons are conveniently located on the outside. To ensure proper fitment, make sure to push the buttons down before inserting the hub into the holder. Due to its tight...

The headphone holder hasn't been adapted to use the same modular mount yet, but hope to update that before too long so everything can be interchanged between the same clamp base. A bolt and nut are included. This design requires very little...

There is over .25 margin between the two parts, should be enough, I advice to add Bison Kit or other strong glue on the lower part of the edge, when its 50% dry (after 10-20 min?) mount to base. No glue should be able to touch the base. After its...

To assemble it, you'll need: 1x 6mm bolt (hex or round head), 60mm in length 1x M6 nut (hex) 3x 5mm bolts (hex or round head), 20mm in length 3x M5 nuts (hex) Furthermore, you will require bolts of various sizes to secure the plate to the item you...

I have designed this part to always have my soldering station handy without cluttering my desk. Assembly is fairly simple and the holder is intended to be mounted using double-sided tape. Feel free to remix if you'd rather use screws or something...

simple mount with screw

Under desk mount for rollo thermal printer. Found a few online that looked nice, but I didn't want to spend the money knowing I could make a version on my own although it would have been faster and technically cheaper :D This model is one piece so...

First, ensure your desk is 20mm thick - modifications can be made to accommodate any thickness. Next, simply remove your country's plug adapter and swap it out for an IEC C7 cable (available at http://bit.ly/2GZ261i ). ...Finally, sand and file the...

  Minimum desk plate thickness: 5mm Maximum desk plate thickness: 65mm   There are two frames. One for headphones with up to 35mm headband width and one for up tp 45mm width.   There are two AIO files (one for 35mm and one for 45mm). ...Those contain...

For those asking why, the answer is 50% why not and 50% I wanted to have a desk lamp that didn't take up desk space. I'm aware its odd, but hey, maybe someone will find it useful. ...I sized the slot in the back to fit my particular desk lamp, but I've...

... beveled edge. ...Added hole for screw thinking I'd screw it into desk, but in the end the fit on desk is snug and a blunt screw applied enough pressure to keep the brackets from moving.Printed with 3 wall layers and 12% gyroid using PETG, no supports.

Effective yet simple headsets designed to fit desks ranging from 1.3 to 1.6 centimeters in thickness are available on the market.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/dWGt0zTfIIa Designed for Ikea Standing desk, about 16.5mm gap

I designed this to hold my headphone on my desk while minimizing the footprint of the setup on my desk space. ... The bracket piece can print without supports however I got better results with supports due to the curve of the top piece.

Designed this in Fusion 360. ...I have a slightly wobbly desk in my office that my printer is on as well. These are designed to go around the 20mm legs on my desk to help support it to the wall to hopefully remove some wobble. ...

One screw velcro mount for cable management

Having just starting to get comfortable where I like things as I use it more and more, I did not want to commit to permanently attaching my desk lamp to the desk. The trouble being that I was unable to find a clamp for my desk lamp that was large...

I've seen innovative designs on thingiverse for headphone hooks, but most of them attach to your desk with a clip that's specific to the width of your desk, may slip off, and again, result in a slight reduction to desk space. This design attaches...

desk mount for 1 inch desks print in two parts with the screw to add a firmer fit

It fits 38mm thick countertops, which is probably the most common dimension for homemade custom desks. Its main goal is to create space for monitor arm clamps and cables so they don't interfere with or cover the LED strip. They will also safeguard...

Works in portrait and landscape format, when changing to a new notebook simply adjust the corner positions ;-) - enjoy the clean desk! If my designs help and you like them, feel free to throw a tip in the PayPal pot. ... Share the link to my designs...

Print 2 of them (one inverted) and screw them under the desk to store a notebook.I added some felt tabs to protect the notebook from scratches.Printed in PLA, 5 perimeters, 80% infill.

Compact quadracopter motor based centrifuge design features a desk mountable configuration with rotors easily interchangeable for various sizes. ...The case accommodates an Arduino base speed controller, resulting in a highly portable and versatile unit...

These are DIY hooks for hanging leads and oscilloscope probes that I created since my desk already has pins for additional shelves. ...Perhaps others may find them helpful as well in the future.

A humble accessory, the headphone bracket, designed to suspend headphones from its sturdy base. ...Secured firmly with a short wood screw, it attaches seamlessly to the edge of a desk, keeping the audio equipment within easy reach.

just a cool tiny desk mountain for looking at. doesn't need any supports. made in blender using the BlenderGIS addon. ... I think the layer lines make it look cool.

I loved the minimalist design by Black-Demon but it didn't quite sit comfortably on my desk. The space between the desk and its surface was 26mm. To get the USB end through the cord hole, I had to carefully sand it a bit. It also features a...

I saw other ones on thingiverse but I wanted to make sure it would fit my desk The desk is 34mm/1.339".. When I finished the design I put it in cura and it was to big I could have printed it with supports a whole almost 8 hours. ...I split the model and...