hotarubi no mori e gin 3d models

Since no matter how slow or fast you unload the filament, it always will get a bulge at the lower end and make the filament significantly thicker. This might be not a problem for the PTFE tube, but it is for the heat break. Thanks to the findings...

There should be little/no friction between FixedInnerSpringAttachment and the ridge on DrumOuter, nor between the springs and EndCap. If needed, carefully adjust the position of FixedInnerSpringAttachment by loosening the M3 bolt. 12. Once a...

Combined with the lash-free Trick Laser arms (with fully-constrained barbells, of course), this is producing very nice prints so far. 5.12.18 UPDATE: I have now run about 100 meters of filament through the new setup, and it continues to work fine,...

This will reduce the potential of errors a lot. As i have no pictures of the single parts I made a rendering: Sounds easy, but wasn't... It took some time to get everything right.</p> <p>The first layer has to be one single area. But all slicers i...

The Hero Me Mutant cooling system prevents filament sagging on extreme overhangs in any direction and is capable of bridging 300mm spans with no supports and no sagging. The Hero Me family of cooling systems is considered by many as the best...

I've modelled a larger 48mm version (STL uploaded, no supports required).I'd already printed four of the original panel clips, so will use these on the back. You can choose if you want to use one size throughout for consistency. The back is the only...

First, I must say that this part is still under construction, as there simply are no nice low profile male 40 pin IDC connectors, and no working gender changers. I need to work on that, for instance create a small PCB with a 40 pin male PCB connector...

After the end of the module is out over the locking piece, keeping it pressed down, you no longer need to hold it down and can slide out the module.https://youtu.be/kBuIak9uanw?si=28jw7GpILdDKn_W7 PRINT SETTINGSNothing in this design needs...

Before his transformation, Finn had performed his blacksmithing duties with a number of tools and had needed a winch to throw out and bring in the ship’s anchor - no more. Strong enough to hoist the anchor as his weapon of choice, he hammers metal...

 The reason it stops is because I have no through axles and the frame starts to push apart at the excape wheel.  I think a through axle from one frame to the other will resolve that.  I have to print new SpringBarrel also since it lifted off the bed...

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).&nbsp; He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

However, the downside to these models is that if you don't have them in your hands, the moving function is of no real use.&nbsp;How awesome would it be to have your favorite articulated model move like, or even better than a Bobble Head does? Well,...

Passive Systems have no "use" function, but the attachment can also have an active system. Wind Power Generator - Passive - Provides 1 Electricity Resource per turn. Solar Panel Array - Passive - Provides 1 Electricity Resource per turn. ...

Motion sensor moved from tabletop bottom to front.1.9 (2019-02-19) • Controller slots, front panels and stoppers changed - easier to insert controllers.0.1 (2018-07-04) • ...PARTSIkea • Ikea LACK Table 55x55cm3 x Ikea LACK tableArticle no:...

Ever since I printed my first #3DBenchy designed by Daniel Norée arround, I've had the idea of making an R/C version of it.But I never got inspiration enough to actually do it, until I saw THENOMADSOUL_ (aka KimDIY) post a cool simple but functional...

If you tighten the screws too tightly at the beginning, the panels may not fit together at the...

Use with MINI Light Bar file.&nbsp;MINI Light Bar Flat: Slightly modified version made to be able to print in the flat orientation, no supports required. Some bridging layers over suspended holes will need to be removed after printing. Textured sheet...

Mariko Takahashi found no evidence that peahens preferred peacocks with more elaborate trains (such as with more eyespots), a more symmetrical arrangement, or a greater length.[16] Takahashi determined that the peacock's train was not the universal...

There is no Z-axis, but a servo that controls the Pen Up/Pen Down. I am using Klipper firmware with octoprint running on a raspberry pi. I started off using Marlin, but couldn't get the servo to work in sync with the X/Y movement. Grbl firmware...

No chance to fit the 20mm high fan into - so I designed the additional case in fusion360. This is to fit on the right side on the moving printhead. I decided to fit the prototype first with double sided tape. It works without the weight of its...

---- Step 1 - Sawing Lamp "Glasses" From a Polycarbonate Twin-wall Sheet There is hardly anyone who will have a polycarbonate twin-wall sheet in stock at home, and no one is likely to buy a whole 1m x 2m sheet just for a few square centimeters. I...

If you want to thanks or support:PayPal Yandex money Benefits: Allows you to reduce the length of retracts and K-factor in Linear Advance, significantly reducing printing time Improved material flow control results in improved printing quality of...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

This improves saftey when carrying as the bow is under no tension until drawn yet can be chambered with a bolt and fired in seconds. This version 1.0 prototype is functional and fairly powerful, but as tension increases, so does the effort required...

The spade connectors should be connected to the NO (normally open) and COM (common) terminals of the switches. The Dupont connectors should be connected to the associated header pins on the GRBL control board. The Woodpecker 3.4 board that comes...

No end stop adjusting...This project is based on SK-Tank CF BMG Dual 5015s Mount by declinox. <a href="https://www.thingiverse.com/thing:5182358">https://thingiverse.com/thing:5182358</a> ) I find his design while looking a project for “MGN12H rail...

The SLS version of Dreadnought was divided into 2 new scale versions of 1:72 and 1:96.One part of Lock (2_Ge_lock_7S_(x4)) you need to print 4 times.New sizes of this model:FFF/FDM 2.0 version 1:48 Scale dimensions:After being printed will stand -...

You will need to remove the knob for the speed control first. SourcesAthruz: HEPPA Filter enclosure with lidMckitrick: 120mm fan mountdfrechette: 1203BB Controller BoxPrint SettingsPrinter Brand:PrusaPrinter:i3 MK3 MMU...

 treasure_chest_v2_lower_end_no_carry_holes OR treasure_chest_v2_lower_end_with_carry_holesPrint 2 copies.Print with the end (the face with four square holes) flat on the bed.Make sure the triangles on the holes are pointed up.The with_carry_holes...

Hope you enjoy! Print Settings Printer Brand: Prusa Printer: MMU2s Supports: No Resolution: 0.3mm and below Infill: .2 and above Filament: any petg recommended, pla okay any Notes: Printing Tips: Level Your Bed: Follow your printer manufacture’s...