hot swap hdd caddy 3d models

This setup allows for hot swap functionality if supported, with drives aligned perfectly with the connector(s). Consider adding tabs to affix to the HDD for easy front access when pulling drives out. Drives protrude 15mm from the front of the cage,...

wanted to make my own hot swap drive cage and here it is. it fits 4x 3.5inch drives vertically in 3x 5.25inch drive bays. you shove the drives in and hotglue the cables in place. almost everything prints without supports. just some small one for...

This caddy system for 3.5" hard disks features * Stackable * Fully 3d printed * hot swap This is designed to fit into an existing enclosure, hence the non standard size. This will not fit into a 5.25" bay! ... Video of it working...

Wanted a hard drive caddy so I could swap hard drives easily in case of failures. Remixed ginge's to allow for 2.5 inch hard drives because I like having a smaller footprint. The second shell has pins that stick up that allow you to attach to...

This 3.5" hard disk caddy system boasts stackable design, full 3D printing compatibility, and hot-swappable functionality. Designed to fit into existing enclosures, it differs from standard sizes, not fitting 5.25" bays. Watch it in action here:...

Swap out the hard disk drive caddy on your IBM xSeries 206m server with a compatible replacement. ...This new caddy is specifically designed to fit the FRU 39R9375 and will also work seamlessly on other IBM servers, including the x306m, x3200, x3250,...

Its purpose is to fit a 2.5" HDD/SSD into a 3.25" hot swap bay. This adapter is providing the shape and connections of a 3.25" HDD to any 3.25" slot including screw holes (where possible). Therefor you can use it in any 3.25" slot although its main...

... the sata cables before applying the glue. Hardware needed: -1x (per caddy) 3mm x 24mm screw -4x (per caddy) Standard HDD Screws -1x 80mm fan -3x Long fan screws -3x SATA Cables -1x Old power supply SATA cable (modular or not) -6x 3mm Plastic Screws

The primary function of this adapter is to provide a seamless integration between your existing storage devices and the 3.25" hot swap slot, ensuring optimal performance and compatibility. With its sleek design, this adapter takes on the shape and...

HDD trays are available for several models, including the JouJye 3051 and 3141, as well as possibly other devices. Due to misplaced original trays, I created my own design to fabricate new ones. ...The custom-made trays fit snugly but securely hold...

This attaches to the rear of a hot-swappable component, ensuring optimal airflow through a carefully designed venting system. ...A compact chamber accommodates a miniature fan, while precise wiring pathways ensure efficient cable management.

The backplane supports activity LEDs, fan connection, PWM fan input, Fan tach output, and drive hot-plug resistors. To use without the activity LEDs, print just the back plane and back cover. Additional models designed to use M3 heat-set...

This is a caddy made for a corsair case. ... Fits a 3.5" hdd but also a 2.5" ssd. I recommend printing in ABS or something heat resistance as in a PC case it can get hot inside.

2.5" to 3.5" HDD/SDD Hot-Swap bay adapter for CoolerMaster Silencio 550 (maybe fits in others...). Based on this idea: https://www.thingiverse.com/thing:4797411 Screws are the same. ... For me more comfortable for using, easy to print.

This is a caddy made for a corsair case. Fits a 3.5" hdd but also a 2.5" ssd. I recommend printing in ABS or something heat resistance as in a PC case it can get hot inside. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: ...

Remix of MegaSaturnv's design here: https://www.thingiverse.com/thing:3739492 Added an extra mounting point to the other side so there are 3 mounting points to the hot-swap tray caddy. ... This has been tested on an HPE DL20 Gen9 hot-swap tray caddy

I designed a straightforward 2.5-3.5in HDD caddy because I needed one that could accommodate my taller server's 2.5 inch hard drive within my Supermicro 3.5 disk shelf. The simple quick print was a necessity, and the outside holes are...

Note that 3.5-2.5 adapters usually place the small drive in the middle of the 3.5, thus it does not fit into the hot-swap slot. This project is modified/optimized for the following factors: 1. minimal size and print cost 2. minimal air flow...

After adding the hot swap back plate (P/N: LAN2-3X) to my Lian Li Lancool Mesh 2 ATX computer case, I was shocked and disappointed to find no availability to purchase additional HD caddies. After initially creating a simple rail design, I decided to...

I needed a server with 3.5" hot swap trays, but I didn't want to put those outdated hard drives in it. The issue was that 2.5" SSDs don't align with the mount holes. You can't drill below to secure it because it has to be flush to fit in the server.

There are numerous 2.5-inch to 3.5-inch drive brackets available on Thingiverse, but only one seems designed specifically for hot-swap server bays with drive caddies. The others fail to mount the 2.5-inch drive in the required position, likely due to...

I couldn't find many quality adapters that allowed me to easily mount a 2.5" hard drive in a hot-swap bay without support on the bottom for SSDs, so I created this one myself. It's really useful because it screws into both sides of a drive tray for...

This adapter allows 2,5'' SATA drives, for example most ssd's to be used more easily in hot swap bay. Requires 2x M3x10 countersunk screws to work NOTE! ...If you are looking for more permanent mount for your ssd inside your case, this one is not...

This is a 3.5" to 2.5" SSD/HDD adapter for some Intel servers. ...Specifically, it replaces the bracket in Intel part number 1B31HY800-600-G There are for modifications: - m3 screws (most recommended) - m3 screws with advanced ventilation -...

This is an adapter for 2.5 inch HDD installation for servers. In particular, it works great for the supermicro server and for my NAS. The current STL file is for ~ 7mm thick solid state drives. To use thicker discs, you will need to use a utility...

The standout feature that distinguishes it from other similar trays available on Thingiverse is its precisely calibrated connectors to match exactly the positioning of those found on a standard 3.5-inch disk, thereby ensuring compatibility with hot...

Holders for choc and MX style hot-swap sockets, for use with hand-wired keyboard builds. Superglue the sockets into the holders, and superglue the holders onto the switch plate/case.The choc holder can be easily printed flat, but the MX-style holder...

https://www.prusaprinters.org/social/114667-racerethan/prints Hot swap afterburner for the HYPR, in similar fashion to my WSPR hot swap afterburner Wiring diagram is similar to a stryfe. Can also use a stryfe motor braking wiring diagram to make...

Hot swap afterburner for the HYPR, in similar fashion to my WSPR hot swap afterburner Wiring diagram is similar to a stryfe. Can also use a stryfe motor braking wiring diagram to make reloading faster. Micro switch is just glued on the side like the...

... go with the motors and connectors for it. superglue loctite of some kind flywheel cage screws x4some rubber bands optional- 2 10-32 thumbscrews for hot swap feature. Crediting Ofp here because thingiverse doesn't have a remix on here. ...