horizontal phone holder 3d models

I tested it out and it seems good, but to stop the weight of the cables plugged into the dock pulling it back I used some Command Strips on the bottom of the dock holder to keep it in place. Bill of MaterialsRequired: 3D printer and filament (inb4...

It is a variation of this thing Filament spool holder (Credits: https://www.thingiverse.com/thing:2047554) I used the credited thing for one half and the custom half to mount it to the 2020 frame. Here you can find the complete model in Fusion 360:...

You will need to remount the extruder up top by the spool holder or swap to a direct drive. The stock motor cable should be long enough to reach (at least on my machine). I don't have the dimensions for the Anycubic Mega Zero V2 but as long as the...

 A flashlight shining through the slit in the hole is your friend.Insert PTFE tubes into the front of the buffer and route to your preferred spool holder system.  If using an enclosure, this will probably involve drilling holes through the enclosure...

That was one of the first mods I did, right after the rear spool holder. My printer is getting old now and the carriage that the cartridge slides into is getting kind of worn and sloppy. It just doesn’t hold the cartridge nice n tight like it used...

The "Abdeckung " parts must be glued to the M3 nut holders of the "Frontplatte" so that the nuts cannot fall out. (Please insert the nuts beforehand). I glue PLA with super glue. In the "Gehaeuse" part there are cut-outs for M3 nuts. Please stop the...

They each had pros and cons. Spool holders and buffer that came with the MMU2(s): Worked well enough but they took up a TON of room (Like an entire dinning room table of space). The spools needed to be placed behind the printer and in line to...

The bolts work only one way, and the distance holder of each gear has to point towards the front of the gearbox. Put the bolt into the lowest bearing, if the round part of the housing is pointing downwards. Push it through, it has to up on the...

- Install the speakers - Route all cables - Cut covers for the speakers (Mine are made out of 1.5mm perforated stainless steel) - Screw the covers and the "Bumper holders" to the base - Slide the bumpers on that, If you want to make sure nothing...

... Also check out my other designs. The tags fit really well with the following designs: Rain Gauge:Colorful Wind Wheel:Also, inspired by the the tagging system, I created a new design for indoor use, you might be interested in:Slide-in Label Holders:

This allows for the using of the stepper shaft has the idler shaft has the initial version of the extruder. New filament coupler design to prevent miss-alignments. Included the stepper motor adapter sketchup file so you can modify/adapt the support...

Rotate parts so that surfaces vital for concentricity (such as bearing holders and pivot block posts) face upward. The only part that is tricky to print is the stick surround. Split this part in half when printing and use high detail. The stick...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

(it is already in the settings in the .3mf files)Assembly:Print all three parts (hull, treads, and gun.)Superglue the treads to the hull.Place the gun on the roof.Superglue works best for gluing it together.It will scale easily if you want a larger...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

DXF and STEP files are available on the project documentation for all panels on all machine sizes In-Lid Spool Holder Our in-house spool holder was also designed with the V-Core 3 enclosure in mind. It can be securely installed inside the V-Core 3...

- https://www.printables.com/model/855331-megalopolis-dice-tower-with-a-story Electronics:Voltage Sensor Box - https://www.printables.com/model/784371-voltage-sensor-box Voltage Sensor Box - SMALL...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

DXF and STEP files are available on the project documentation for all panels on all machine sizes In-Lid Spool Holder Our in-house spool holder was also designed with the V-Core 3 enclosure in mind. It can be securely installed inside the V-Core 3...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

It can be mounted anywhere, and the cables can be routed directly within the holder. I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). ...Il...

https://www.amazon.com/icepc-Channels-Cooling-Controller-Interface/dp/B08CXYZLBK The object on the upper rear crossbar is a holder for 1.5" PVC pipe. Print two of them and use 2 90 degree elbows and some pipe and make a spool holder. EDIT...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above. Support enforcers are neededNo gluingEasy to printDesigned on...

Glue is not needed on the outside of the Dupont holder. General: There are quite a few M3 inserts used in this project, and they should be heat set, but I glued them in on my kits. I decided to glue them in using clear Gorilla Glue since I have no...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

You can either modify the models slightly to increase/decrease the size or use the horizontal expansion setting in Cura adjust the part prints. ### Assembly Assembly is fairly straight forward and most of it should make sense off of the pictures....

The outside surface will be sanded anyway, so don't worry about those so much. Sand all the outside surfaces ALONG the wood grain lines (horizontally), using 80 grit sandpaper. Take care not to sand across the grain (vertically). This removes...

Tuning is fairly easy, and it's even easier if you use an electronic tuner or a tuner app on your phone or computer. Here's an online one that seems to work well: https://theonlinemetronome.com/instrument-tunerTuned too highTuned just rightTuned too...

If you have installed the latest firmware, you have the possibility to reverse the direction of rotation of the extruder without needing to touch the wires, go to the settings, keep the button pressed for 2 seconds, a new menu appears, click on...

Initially I had planned a voltage converter module (present on one of the photos, but do not take it into account), but after the tests, it works better directly without the converter.You will need:3 batteries Li-Ion 186501 fan :...