hook for headphones 3d models

The Area-51 Headphone Hook gives you a handy spot to store your gaming headset when it's out of commission. ...It easily attaches itself to the front bottom lip of the latest Alienware trinity case.

... version of http://www.thingiverse.com/thing:612014 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=612014 Adjusted desk thickness to 15.5mm and headphone shelf a bit (6.35) for a basic plantronics headset

Simple remix to adapt the headphone holder to my Linnmon desk

... top of the desk at the opposite end of where you attached the first screw. 4) Place the headphones on the shelf that was specifically designed for them. ... 5) To place the headset, attach the screws into the hole that is in line with your earbuds.

A simple adaption to allow for hanging your headset or other bags etc under a shelving pine desk.

Moreover, reworking the clip over the edge of the shelf put it under stress, causing it to open up slightly - making it increasingly easy for a knock to dislodge the holder from its shelf edge perch.\r\n\r\nA redesign was thus necessitated. The...

This is my submission to the SilverStone wall-mounted headphone stand design contest, in partnership with Linus Tech Tips. Cast your vote by downloading and sharing my entry. ...For more information on the contest, check out Linus' video:

A remix of the original design by krbrowning is presented, with full credit given to the creator for their work. ...This version has been adapted specifically for use with two small nails in place of a screw.

Simple, no support hanger for headphones that slips over a "large" (17003es) command hook bracket piece. I couldn't get the strips to adhere well to PLA so I made this so I wouldn't have to worry about it. ...Just store the hook Category: Organization

Simple, a dedicated headphone hanger designed specifically for large command hook brackets. I created this because traditional adhesive strips failed to stick properly to PLA materials, causing frustration with every attempt. ...This solution eliminates...

... these guidelines: - Set the width to 20 units. - Adjust the desk height to 6 units. - Increase the thickness to 5 units. - Disable the jack option by setting it to 0. - Raise the hook height to 15 units. ...- Deepen the overall design to 30 units.

... was made using Customizer! ...(http://www.thingiverse.com/apps/customizer/run?thing_id=44705). For this specific design, the desk height is set at 45, no jack, a depth of 67, thickness of 9, hook height at 17, and a width of 25.

Instructions to Craft Your Unique Macrame Desk Organizer Select from these customizations: Width: Enlarge the overall design to 20 units Height of Desk Holder: Set the depth at a precise 17 inches Elevate Your Organizing Game: Configure the hook...

Xbox 1 controller / headphone with hook for wire

A sleek headphone hook designed specifically for 19 mm boards commonly found on shelves.

I designed an iPad adapter from a portable DVD holder with an optional headphone hook. Since I already have two DVD holders installed on my car's headrest, I created this adapter to use them with iPads. The design is sturdy enough for kids and only...

I created an adapter to turn portable DVD holders into iPad stands with an optional armrest for headphones. Since I already had installed two DVD holders on my car's headrests, I made an adapter so I can use them with iPads. The design is sturdy...

Design Customization Customized version of http://www.thingiverse.com/thing:1409239 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1409239 Instructions Using the following settings: Width 30 Wire width 6.5 Headband...

I created a revised version because I wanted to tailor it precisely and included the 123dx file as well.\nPrint Settings\nPrinter:\nBigBox 1.1 Dual\nRafts:\nNo\nSupports:\nNo\nResolution:\n0.35\nInfill:\n15%

I made a new one because I needed to customize it... and added I the 123dx file too. ...Print Settings Printer: BigBox 1.1 Dual Rafts: No Supports: No Resolution: 0.35 Infill: 15% Category: Organization

I made a new one because I needed to customize it... and added I the 123dx file too. ...Print Settings Printer: BigBox 1.1 Dual Rafts: No Supports: No Resolution: 0.35 Infill: 15% Category: Organization

Here's a revised version of the sentence rewritten in a more dynamic and engaging way: I whipped up a snazzy remix to squeeze this one onto my prized IKEA shelf, where it now proudly takes center stage.

Customized version of https://www.thingiverse.com/thing:44705 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=44705

I'm Unable to Generate Content Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=44705 Instructions Using the following settings: Width is set at forty units. Desk height stands tall at forty units as...