hood rod holder 3d models
401309 3d models found related to hood rod holder.thingiverse
Hood rod holder for Chevy Volt 2011-2015 MY, GM. ... For easier extraction of the hood stop.
thingiverse
Hood/bonnet rod holder for a ford escort 1998 will fit anything with a almost square hole with a width about 7.5mm and the rod with 7,6mm diameter. Installed on the car a few days ago. it bites the rod quite strongly, but no signs of fissures yet. ...
thingiverse
Hood prop rod holder. ...Use ABS or nylon for high temperatures For Honda City
thingiverse
After some trial an error I noticed that it had something to do with the Hood rod, since removing it took care of the sound, the original grommet is made of hard plastic (I suspect some sort of Nylon) and it seems like once removed it breaks and...
thingiverse
This is a Honda Hood Prop Rod Holder Clip that I reverse engineered (and over-engineered) to replace the original broken one. I see online that this should work for the 2006-2009 civic but the OEM part number is 90672-SJ4-013 just in case it fits...
thingiverse
Yugo P/N 4427542 Holder clip for the hood prop on a Yugo. Print requires a #4-1/2" screw. Lay the print on its side and set supports to Bed Facing. ... It doesn't see much stress, I only printed it with a 30% infill.
grabcad
Suzuki Swift MKII Hood Rod HolderHood Rod HolderBonnet Rod HolderSuitable for 3D printing with supportI would suggest to measure the rod Diameter and change the model accordingly. ...The clip feature works very well.
thingiverse
My car's hooh rod holder clip is broken and i designed this spare part. ...It worked for me :)
thingiverse
Best to print out of Nylon. I tried other materials and they break apart. ...I put two in there in case an extra is needed.
cults3d
Rubber Grommet printed with NinjaFlex, to substitute the original hard plastic part which created noise under certain conditions.
thingiverse
This is a hood rod clip for the Jeep Wrangler TJ printed in ABS. ...The version "2.Brocho varilla cofreTornillo" has a space for a nut to install more easyly.
thingiverse
Broke my 22 year old OEM Nylon rod holder. So, naturally, decided to 3d print one. Was more difficult than I expected simply because I don't have nylon filament. I printed this with PETG, and the only issue is that it was really difficult to get in.
thingiverse
2003 Jeep Wrangler Rubicon Hood Prop Rod Holder Clipprint PETG @ 100% infill, or as i prefer, 99999 bottom (solid) layersif the print does not work well, please let me know. this is a modified version after i had to file the original design down to...
thingiverse
This is for the small piece holding the rod maintaining the hood open. ...Best results in Nylon.
thingiverse
A replacement clip for early to mid 2000s Honda hood prop retainer. Tested and working on a 2001 Honda Civic LX. ...Enjoy :)
thingiverse
I broke the clip that keeps the bonnet rod in place, so i design a new one. ... You will need a screw in the middle. Download: https://cults3d.com/en/3d-model/various/hood-bonnet-rod-holder-renault-clio-2-ii-fase-2-ii
thingiverse
Autoparts - a holder of hood rods for Isuzu Trooper/Bighorn 87-91. ...The part was strengthened a little with stiffening ribs in weak places.
cults3d
I broke the clip that keeps the bonnet rod in place, so i design a new one. ... You will need a screw in the middle.
myminifactory
replacement part for 06 dodge hood rod holder. ...This may fit other makes of autos
grabcad
Hood Prop Rod Holder / Support Rod Retainer Clip
thingiverse
Hood prop rod holder for a RENIX era MJ/XJ. Not sure if it is the same in 97+ Cherokees, but should fit the older ones. Use the slicer to lay it flat on the angled side and so that the bottom of the clips are touching the plate. ...you may need to play...
thingiverse
Hood rod socket for skoda octavia. ...Fits the 2012 model. I recommend a high infill % and printing sideways with supports so that the force applied by the hood rod is not paralell to your print lines.
thingiverse
this is a bracket for the rod that supports the hood in the Honda Cars I printed in PET-G to make it stronger 100% infill
thingiverse
Hot rod hood scoop has holes below for magnets along with suction channels. ...Because of the suction generated by these channels the thing sticks to the surface more as the vehicle goes faster.
pinshape
SummaryHot rod hood scoop has holes below for magnets along with suction channels. ...Because of the suction generated by these channels the thing sticks to the surface more as the vehicle goes faster.
thingiverse
This part was previously replaced with a generic part purchased in a bag with about ten different sizes/shapes of hood rod clip. This suggests that, although the part was designed to replace a part in a 2008 Chevy Equinox, the specifications may...
thingiverse
This thing is the part that supports and pivots the rod that holds open the engine compartment hood of a car. It was designed to fit Honda civic but it most likely will fit any other vehicle make. The part was made of flexible PLA which is necessary...
thingiverse
This is a bushing to fit a 7.6mm rod onto a 16.3mm round hole. ... I've installed it on the car a few days ago, it`s still fit with no looseness.