honeycomb storage 3d models

 I had a small sliver of space on the wall under the unit heater, so I printed a honeycomb storage wall (thanks to rostap of course) (https://www.printables.com/model/152592-honeycomb-storage-wall) and off I went.You have to print the M3 inserts...

A Memo box with a honeycomb texture, designed in Fusion360. Print time: 5 – 6.5 hours at 100% scale (depending on settings)Dimensions: 9.5 x 9.5 x 7 cm (length x width x height)Weight: 45 grams Tip: try to calibrate your retraction settings before...

A Memo box with a honeycomb texture, designed in Fusion360. Print time: 5 – 6.5 hours at 100% scale (depending on settings) Dimensions: 9.5 x 9.5 x 7 cm (length x width x height) Weight: 45 grams Tip: try to calibrate your retraction settings...

A Memo box with a honeycomb texture, designed in Fusion360. Print time: 5 – 6.5 hours at 100% scale (depending on settings) Dimensions: 9.5 x 9.5 x 7 cm (length x width x height) Weight: 45 grams Tip: try to calibrate your retraction settings before...

Printing puzzle parts with precision, using a 1mm width nozzle and zero infill for maximum speed. Spiral vase mode is also available. Boxes are printed with the same 1mm width, ensuring a seamless finish. The layer height is set to 0.3mm, allowing...

A simple and strong holder for the DREMEL 2200 torch.Works with a single hollow insertMy print is with .8 nozzle, no support, 3 walls, PLA+Any feedback would be appreciated...Enjoy!Original model at thangs.com: https://social.thangs.com/m/996010

Change the orientation of the battery holder some that two batteries can be held sideways to the wall. ...Lets you save some wall space for smaller batteries (large batteries will still take up the same space as they do on the single mount)

Holds your drill bits from 1mm to 10mm and looks nice :)Easy to print, no support needed.

Based on https://makerworld.com/en/models/91868#profileId-98268 by @kobu83 and @rostap's https://makerworld.com/en/models/22521#profileId-27457 - added pegs to mount the tools https://makerworld.com/en/models/14462#profileId-37136 to the rear of my...

Remix of: https://www.thingiverse.com/thing:5480197

<p>Used:</p><p>Voxalabs Aquila</p><p>eSUN PLA+ Black</p><p>0.2mm layer height</p><p>25% infill, more the better really.</p><p>Used ironing so get a smoother surface, but unsure if this is really needed.</p>

<p>Part needs support.</p><p>stl's with 12mm and 14mm gap between hooks and with two different cylinder length.</p>

3D printer pen holder for my SCRIB3D P1 3D Printing Pen.  A 25mm inside diameter works for this pen. ... I added 26, 27, 28, 29 and 30mm sizes to fit other pens.

<p>Its silly.</p><p>This works with the insert-empty.stl, make sure to use supports and print with the tip of the nose pointing up.</p>

I've printed mine in PLA-CF,  PLA & PETG should work just as fine. this will need Support, for your convenience the 3mf file is setup for a Bambulab printer with AMS using PLA-CF + Support for PLA as interface.

I completely remade the holder but used the original as an inspiration. Watch out, dimensions are probably different and therefore not compatible with the original.The original design by @kitlaan had "lips" that interlocked together to make the left...

Print two each of the included .STL files in the original orientation. ...Insert into wall at appropriate distance.

This design draws inspiration from: https://www.thingiverse.com/thing:3220489 https://www.thingiverse.com/thing:1743145 The storage modules offer endless expansion potential, but due to their 55-degree slant, they can only connect in a single...

Customized version of https://www.thingiverse.com/thing:362924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=362924 Instructions Using the following options: number_of_columns = 4 wall_thickness...