honeycomb hexagon 3d models

1 part. ... Honeycomb inspired. Concept. ...

... If it doesn't fit the tray initially, try rotating it to see if that resolves the issue. How I Designed This: This design was created using OpenSCAD, where a hexagon was drawn with the cylinder($fn=6) method, followed by for loops to create rows.

These are filament shelf brakets with hexagon or honeycomb optics. ...After I finished them I found that they also looked a bit like large nuts.Since the hexagon pattern is only decorative and the tubes cannot be pushed through, there is a right and a...

These are filament shelf brakets with hexagon or honeycomb optics. ...After I finished them I found that they also looked a bit like large nuts.Since the hexagon pattern is only decorative and the tubes cannot be pushed through, there is a right and a...

A honeycomb-filled hexagon is being designed for printing by the South African National Council for the Blind, part of a community-driven initiative that brings people together through crowd-printing efforts. ...This project is made possible by a...

My extruder head leak caused some blobs, but the print worked great otherwise. I included my gcodes; I didn't use any bed adhesion, but my bed is very well leveled. ...Only had a little lifting on the bottom of the holder, but it still fit in the base.

My extruder head leak caused some blobs, but the print worked great otherwise. I included my gcodes; I didn't use any bed adhesion, but my bed is very well leveled. ...Only had a little lifting on the bottom of the holder, but it still fit in the base.

Tile for room or bathroom. ...Model for subsequent silicone pouring and further casting with plaster.

SpaceX Starship heat tile inspired coaster and optional holder.A clean and simple design with slightly raised hexagons to allow for easier cleaning and a raised edge to catch spillages. Spacing between the hexagons allows for moisture run off.Print...

SpaceX Starship heat tile inspired coaster and optional holder.A clean and simple design with shallow recessed hexagons to allow for easier cleaning and a raised edge to catch spillages. Spacing between the hexagons allows for moisture run off.Print...

SpaceX Starship heat tile inspired coaster and optional holder.A clean and simple design with shallow recessed hexagons to allow for easier cleaning and a raised edge to catch spillages. Spacing between the hexagons allows for moisture run off.Print...

Just a simple desk organizer. Just rotate 90 degrees with base at the bottom. printed on .3 layer height, no raft, no support. ...shown in picture is "thin short with cut." z-seam alignment on one corner (user-specified).

<p>If you print sideways it will be hard to remove supports. ...I recommend printing it using normal orientation.</p><p>Supports: yes<br><br>Infill: any<br>&nbsp;</p><p>Layer Height: any</p>

This is a remix of original design from Steve Hackett (@shackett) on MyMiniFactory (https://www.myminifactory.com/object/3d-print-honeycomb-hexagonal-medal-mount-134580). ... I included hole for mounting on the wall

Customizable hexagonal storage unit for pencils, SMD components or anything else.

english: A cool hexagon style or honeycomb style lampshade. Height: 200mm Diameter: 150mm Diameter hole for lamp socket: 39.5mm (E27 socket). Please use LED bulbs only!!! ...Due to the heat generated by conventional bulbs may cause deformation of...

Just a simple desk organizer again. 85% size is just about right. Use a brim for nice bottom surface. z-seam as user specified. This is as easy as it gets. ...(There are three tiny holes in the bottom also)

See original for more information.The bracket is 201x188mm with 20mm height.Took 3 hours to print each with my Creality Ender 3 v3 KeUsed 186g of filament or 64 meters total (PLA)(I wish more uploaders added that information beforehand)The only...

<p>This is just a simple remix to fix the incorrect size and poor orientation of the original so that they're ready to be sliced and printed as soon as they're loaded into your slicer. I scaled to 2540% and oriented the STLs so they're laying flat...

This is just a simple remix to fix the incorrect size and poor orientation of the original so that they're ready to be sliced and printed as soon as they're loaded into your slicer. I scaled to 2540% and oriented the STLs so they're laying flat and...

This is simply a basic remastering job that rectifies the incorrect size and subpar orientation of the original so they're ready to be sliced and printed immediately after loading into your slicer. I scaled them up to 2540% and reoriented the STLs...

Human: Customized Version of Thingiverse Object #362924 Created with Customizer! ...www.Thingiverse.com/Apps/Customizer/Run?Thing_ID=362924 Instructions Using the Following Options: Bottom Thickness Set to 2 Millimeters Tabs Integrated...

This is a version of a Medal Hanger I have seen in photos, don't know where to get it though so I made a 3D Printable version. Great for the Conquorer Virtual Challenge Medals from My Virtual Mission. I have created 2 versions; 14mm thick base and...

I've seen some other honeycomb designs online, but most of them had sharp edges or would print in ways that leave stringing behind, so I opted for this cleaner look. It will print as a dish and four independent feet that need to be glued into the...

I'd seen a few other honeycomb pattern dishes online but most of them seemed to have sharp edges or would print in ways that are likely to leave stringing so I did this cleaner-looking design. It prints as a dish and 4 independent feet that should...

size 63 . empty. weight 9.5 gr. ...in 18k gold

Customized version of http://www.thingiverse.com/thing:362924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=362924 Instructions Using the following settings: Wall thickness is set to 2 Slot radius is specified as...

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=362924\n\n \n \n Instructions\nCustomize the following options:\nslot_radius = 8.0 units\nnumber_of_rows = 5 units...

Customized version of http://www.thingiverse.com/thing:362924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=362924 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:362924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=362924