honda odyssey universal phone mount by 3d models

This is a universal phone (or any other rectangle) mounting system. The phone mount swivels on the base and has a retaining ring to lock the swivel angle. Build instructions: 1) Snap USPM_Pin into USPM_Top and then thread it onto...

This is a universal phone (or any other rectangle) mounting system. Build instructions: 1) Snap USPM_Pin into USPM_Top and then thread it onto USPM_FlatMountBase. ... 2) Attach USPM_FlatMount to USPM_FlatMountBase with an M4 x 4mm bolt and nut.

honda odyssey odysey oddyssey 2010 2011 2012 2013 2014 van minibus minivan family japan usa car mpv

This is a replacement back for the Honda Odyssey keyfob that comes with the key. ...Print Settings Printer Brand MakerBot Printer MakerBot Replicator 2 Rafts No Supports No Resolution 0.1mm Infill 15%

This custom shade clips seamlessly over the overhead light above the sliding doors of a 2015 Honda Odyssey EX, with potential compatibility also extending to other years and models.

This is a plate I designed for the center console of our 2018 Honda Odyssey. The plate makes the bottom of the console into a separate compartment. ...Fits very snugly.

This is a plate I designed for the center console of our 2018 Honda Odyssey. The plate makes the bottom of the console into a separate compartment. ...Fits very snugly.</p>

This is a shelf that I designed to fit in the center console of my 2018 Honda Odyssey. There appears to be a lip towards the bottom of the center console compartment, however, there was no provided shelf. ...This shelf fits snuggly and securely.

I couldn't find one of these online so I had to make my own. ...It fits a 2004 Honda Odyssey for sure, but it's possible that it will work for other models. ...It's just a replacement lever for the seat recliners.

I'm replacing the faulty hood latch clip on my Honda Odyssey with this sturdy new part. To take out the old clip, simply squeeze it gently with pliers until it comes loose, then pull it right out. This replacement clip should click easily into place...

Honda Odyssey 2008 sun shade clip. This secures the sliding doors' sun shade in place. I reverse-engineered this part from a broken one, so it may not be exact, but works perfectly in our van. A higher-quality print might hold up even better over...

I've found a simple solution to dim the overhead light above my daughter's sliding doors in our 2015 Honda Odyssey EX, and it fits perfectly. The idea is to create a clip that will cover the overhead light during late night trips when my daughter...

These lamps are generally priced under $15 and offer flexibility as they can be posed in different positions: US customers can find this product on https://www.ikea.com/us/en/p/tertial-work-lamp-with-led-bulb-white-60424987 Australian customers can...

The mount is very universal, accommodating all mobile phones, whether Apple or Android, between its two parts. There's also enough space between the pieces for charging your phone while it's docked. Print Settings: Printer: Monoprice Maker Select...

It allows you to film in a birds eye view, looking down at a table, with the added advantage of built in lighting. Great for craft videos or streaming lecture notes. These lamps are usually sold for less than $15, and are pose-able: US:...

This is a remix of the universal tripod mount by Ney Frota https://www.thingiverse.com/neyfrota I have an iPhone 12 pro and I use a wallet flip cover case, so the only change I made was to extend the jaws to accommodate the size of my phone and allow...

Its universal phone mount for bike. Mount to bike width tube 36 mm diameter Works on elastic bands Min phone size 140|70mm (diagonal 6 inch) Min phone size 170|100mm (diagonal 7,7 inch) Holds up perfectly. ...Just put on enough rubber bands Print...

High detailed model created by SQUIR team.

Its universal phone mount for bike. Mount to bike width tube 36 mm diameter Works on elastic bands Min phone size 140|70mm (diagonal 6 inch) Min phone size 170|100mm (diagonal 7,7 inch) Holds up perfectly. ...Just put on enough rubber bands

Its universal phone mount for bike. Mount to bike width tube 36 mm diameter Works on elastic bands Min phone size 140|70mm (diagonal 6 inch) Min phone size 170|100mm (diagonal 7,7 inch) Holds up perfectly. ...Just put on enough rubber bands

Its universal phone mount for bike. Mount to bike width tube 36 mm diameterWorks on elastic bandsMin phone size 140|70mm (diagonal 6 inch)Min phone size 170|100mm (diagonal 7,7 inch)Holds up perfectly. ...Just put on enough rubber bands

... it from being dislodged during use. Simply print this horizontally with a support raft, despite the resulting appearance on top, as it will be concealed within the console. Be cautious of delamination issues by sticking with horizontal prints.

This intricate model was crafted by SQUIR and is ready to render in 3ds Max without any additional plugins. All necessary materials, lightning setups, and background configurations are included. The scene setup corresponds with 3ds Max 2012 but can...

High-precision model created by the expert team at SQUIR. Rendered seamlessly in 3dsmax with VRAY technology, it's ready to bring your visions to life. Originally rendered using 3dsmax 2015 and vray3.20, this masterpiece boasts intricate details...

High detailed model created by the talented team at Squir. This exceptional model is ready to be rendered in 3dsmax using VRAY. Rendered seamlessly with 3dsmax 2015 and vray 3.20, this scene includes all lightning effects, materials, and background...

Assembly video: https://youtu.be/dTpAveY3pv4 Remixed from https://www.thingiverse.com/thing:4625349 Inspired by https://www.thingiverse.com/thing:2423960 Suitable for phones from about 55mm wide to 95mm wide Use metal M5x25 bolt if possible I used to...

Assembly video: https://youtu.be/dTpAveY3pv4 Remixed from https://www.thingiverse.com/thing:4625349 Inspired by https://www.thingiverse.com/thing:2423960 Suitable for phones from about 55mm wide to 95mm wide Use metal M5x25 bolt if possible I used to...

Inspired by cswaim's clamping method, this universal phone mount features a wider clamping surface and tightening nuts for added security. Printable in 3.5-4 hours on standard settings without support, optimized for PLA. To assemble, attach two 4"...

This is a universal phone holder base that mounts to the back of the C6s center console. The hole is 4mm and can be threaded in M5. I used a ball on an M5 thread to mount my QI charging holder. Optimized for Resin printing (so..not optimized).

Adapter to mount my "Dollarama Tech1 Wireless Charger" phone holderto the dash of my Honda Element. Prints with supports touching buildplate Don't think they sell this mount anymore, but a good start for anyone else looking to build a phone adapter!