honda element hood latch 3d models

I tried the original printed clip but found out it was to short for a 99 Honda Civic so I extended it.

These old Mercedes W123 cars often have a faulty bonnet (hood) latch pull handle that breaks easily. This problem may also affect W124 models. The curved design of this part requires some finesse when replacing it. To avoid any potential issues, I...

The engine compartment prop holder consistently fails on every Honda vehicle I've owned. ...This time, I have the capability to design and produce a functioning one that won't break!\nIt is designed for the 1992 Civic model.\n\n \n ...

The element has a slope, so added a taper to level out the holder. You could really just slap it on any flat surface. I'd like to add a business card holder underneath at a later date. ...The ledge probably doesn't need to be that far out, flush will...

My hood release handle has been broken for years now, so I've resorted to using a pair of vice grips to open it every time. The trick is that the shaft is extremely well glued or threaded to the metal rod it's attached to, leaving it in place when...

An OEM-style cleat for a lockable Jeep Wrangler hood. ... Tested multiple layer orientations, and the only one that didn't split was laid flat, with supports for the lip.

Replacement part for my 1991 Honda CRX fuel door latch, suitable for repair. This replacement component works perfectly well on my vehicle. To make sure you achieve the same result on your car, pay close attention to these instructions carefully.

I am not the original writer of this material. ...I discovered it online and copied it down.

Backup camera mount for Honda Element

2012 Honda Civic hood rod clip. Added side walls to prevent hood rod from contacting battery terminal if the clip breaks. ...Designed for 8.2mm Rod

Drivers seat height adjustment knob for my 2007 Honda element friction fit

Replacement latch clip for Vision Chef 0602 kitchen hood. ...Print on side with supports.

The correct replacement component for a Honda hood prop rod retainer clip on an EJ/EK engine is the part numbered 90672-SJ4-013.

A replacement elbow rest latch for a 2005 Honda Hybrid Civic is needed.

3D printed molds are utilized for crafting latches that secure car hoods. ...For more information, visit www.TRINOTA.com.

Remix of another hood latch pull. Remodeled it so that it's easier to print. ...Also ended up making it slightly shorter, but is still long enough to pop the hood. Category: Automotive

Made this Hood prop rod latch to fit my Datsun B110 1200 Sedan, but it may fit other Datsuns or vehicles (square hole 7X7mm).

This is a custom-designed Hood Prop Rod Holder Clip for the Honda Hood, meticulously engineered to replace a broken OEM part. Online research indicates compatibility with 2006-2009 Civic models; however, the original part number - 90672-SJ4-013 -...

I created a retaining clip for the hood prop rod in my 2003 Honda Civic. Other designs on Thingiverse failed to meet my needs, so I designed my own version in May of 2018. If you find this helpful, consider leaving a tip. ...Your support is greatly...

... the latch on the driver's side of the car and press down on it with your finger or a flathead screwdriver. As you apply pressure, the latch will release and swing open, allowing you to lift up the hood and gain access to the engine area underneath.

Simple shift lock release cover for my Honda Element. There is a slight curvature to the top surface to match the curvature of the shifter panel, so reduce layer height significantly or sand it if you want that to look good. ...You should also print it...

This file is for plugging the hole in the spare tire cover on a Honda Element in the cargo area. ... It will only work if printed in a flexible filament as it has to deform to push through the hole and lock in place.

Adapter to mount my "Dollarama Tech1 Wireless Charger" phone holderto the dash of my Honda Element. Prints with supports touching buildplate Don't think they sell this mount anymore, but a good start for anyone else looking to build a phone...

My hood lever in my Honda CR-V II broke down, so I replaced it with a beautiful new one. I secured the new one with a 5mm zip-tie. The new lever sat on top of the old broken one. ... To rebuild the lever: ...

I had to swap out the Aux Audio input jack in my Honda Element, which gave me an idea - a simple adapter that lets me access the pins behind the dashboard and pull them out more easily. It seemed worth sharing with others. ... <iframe width="725"...

This is a brake light cover designed specifically for the middle (third) brake on the Honda Element. I offer these items in my Etsy Store, which can be found at https://www.etsy.com/shop/westrealm. These covers fit all years of the Honda Element...

 On the first day the little latch that holds the hood down, despaired in the yard some where.The latch was made with Tinkercad and sliced with Prusa Slicer, and printed in a Sovol SV04.The changed I did make is. The original latch had a slot in the...

After both sides of my hood latch handle breaking off, I designed this handle to slip over the remainder of the handle. I have had it on the car for years and it works great. ...I printed out of black PTEG

Thus is Hood Release Latch for Mercedes CL500 W215.This is very hard to find online for purchase, so I modelled it.Better print it using PETG to handle better outdoor temp or even ABS. ...I test printed it using PLA and PETG but not ABS.

This is a brand new replacement hood latch release handle specifically designed to fit a 2001 Jeep Grand Cherokee WJ model. ...I needed one myself after my original broke, so I took the initiative to create a precise replica as a direct substitute.