homematic ip 3d models
3538 3d models found related to homematic ip.
thingiverse
Halterung für die Spiegelfolie von dem Homematic IP Fenster- und Türkontakt. ... Die Spiegelfolie auf die breite Seite und das doppelseitige Klebeband auf die schale Seite kleben.
thingiverse
Aufsteller für den Homematic IP Wandthermostat wie HmIP-WTH-2. Der Wandthermostat wird mit der mitgelieferten Befestigungsplatte aufgeschraubt. Zum befestigen werden 2x Senkschrauben 2,5x10 oder 3x10 benötigt. Der Aufsteller kann aufrecht...
thingiverse
Install Homematic IP Switch securely by fastening it to its case using three M3x10 screws. ...Be mindful of the electrical current, as handling it poses a significant hazard – exercise extreme caution when working with it, and do so at your own peril.
thingiverse
For all those who can not accommodate Homematic IP devices in flush-mounted boxes, because there is too little space, these adapters are perfect. I printed them in PETG, but also goes very well in PLA. The adapter puts the box 25 mm out from the...
thingiverse
Homematic IP (!) Fensterkontakt Abdeckung. ... Homematic IP (!) Window Sensor cover
thingiverse
Wandhalterung für Homematic ip access point Wall bracket for Homematic IP Access Point
thingiverse
Ersatzteil für den Homematic IP Wettersensor Stützstruktur nötig!
thingiverse
Doormount for a Homematic IP Doorsensor. ...No screws are needed, use adhesive tape instead.
thingiverse
Wallmount for a Homematic IP Access Point using double sided tape.
thingiverse
Deutsch: Wandadapter für Homematic IP (benutze HmIP-STHD) um Distanz zwischen dem Raumthermostat und einem existierenden Kabel zu schaffen. ... English: Wall mount for Homematic IP (use HmIP-STHD) to distance the room thermostat over a existing cable.
prusaprinters
Deutsch:Wandadapter für Homematic IP (benutze HmIP-STHD) um Distanz zwischen dem Raumthermostat und einem existierenden Kabel zu schaffen.English:Wall mount for Homematic IP (use HmIP-STHD) to distance the room thermostat over a existing cable.
thingiverse
Holder designed to hold the Homematic IP Thermostat in an 20° angle. Print it in PLA oder PETG and use two M3 screws to attach it to the backplate. ...No supports needed.
prusaprinters
A small and clean stand for my Homematic IP wall thermostat. Print it without supports in two pices. I tested it with the following Homematic devices:HmIP-WTH-1 (thermostat)HmIP-WTH-A (thermostat)HM-PB-2-WM55HmIP-WRC6HmIP-WRC6-A…maybe many...
prusaprinters
Holder designed to hold the Homematic IP Thermostat in an 20° angle. Print it in PLA oder PETG and use two M3 screws to attach it to the backplate. No supports needed. ... Print Settings Printer Brand: Creality Printer: CR-XRafts: No Supports: ...
thingiverse
... like these https://www.elv.de/schliesser-mini-drucktaster-1-polig-rot.html ones. And, of course, it all connects to my ELV Homematic IP module board, the HmIP-MOD-OC8 https://amzn.to/2st2Zp0. ...I've got 25% infill and four wall lines set up.
thingiverse
Casing for Homematic IP Doorbell Signaling Recognition HmIP-DSD-PCB https://amzn.to/2WZl9j5
thingiverse
I create a custom 90-degree adapter for my Homematic IP window and door contact (HMIP-SWDO) to facilitate easy installation in my garden shed.
thingiverse
------------------------------------ Da ich es nicht mag, meine Wände unnötig zu durchlöchern, habe ich diesen Wandhalter zur Befestigung des Homematic IP Access Points HmIP- mit nur einer Schraube entworfen. Der Access Point rastet fest in die...
cults3d
Simple housing for the Homematic IP doorbell sensor HmIP-DSD-PCB. So that the board fits optimally into the housing I soldered the switch S1 rotated by 180 degrees. The board is fixed with the supplied M3 polyamide screws. The housing parts are...
thingiverse
Hello,\r\n\r\nI have a wall mount here for the Fritzbox 7590 and Homematic IP AccessPoint.\r\n\r\nThe holder can be secured to the wall with simple double-sided adhesive tape.\r\n\r\nScrews: 4x 3.2x20mm screws (simple screws for switch installation)
thingiverse
Simple housing for the Homematic IP doorbell sensor HmIP-DSD-PCB. So that the board fits optimally into the housing I soldered the switch S1 rotated by 180 degrees. The board is fixed with the supplied M3 polyamide screws. The housing parts are...
thingiverse
Simple outdoor housing for the Homematic IP Keypad HmIP-WKP. I printed the basic box in normal PLA, and the cover with extra strong black Glass Fibre PLA. Basic protection against sun light and (limited) rain (no IPx rating). - The Keybatic...
thingiverse
This is a table stand for the Homematic IP and MAX! Thermostate. Both share the same ground plate. From https://www.thingiverse.com/thing:2755553 I used the clamps. The rest is designed from scratch. The stand has an angle of 60°. Its inner...
prusaprinters
Adapter um ein Homematic IP Gerät an ein Danfoss RAVL Ventil anzuschliessen.Die Teile sind einfach zu drucken, keine supports nötig. Von PLA ist wegen der Temperaturen abzuraten, ich habe PETG genommen, das geht gut und ist auch leicht zu drucken.
thingiverse
DE: Diese Halteplatte dient zur Befestigung von batteriebetriebenen Homematic IP-Geräten im 55er Format (z.B. Schalter, Bewegungsmelder, Wandthermostate) in der Gunsan Visage Schalterserie. Die Originalplatten sind hier zu dick, sodaß der Gunsan...
thingiverse
The two clips that hold the circuit board should be pressed down with a hotter screwdriver to secure the board in place. Have fun! ...Update: Version 2 - corners of the lid modified, etching on the board slightly enlarged
thingiverse
With this adapter you can install a Homematic / Homematic IP heating actuator on a underfloor heating with a RTL thermostat from oventrop