homemade s10 v8 motor mounts 3d models

So after spotting some posts about how the motor mount on the FT Edge can become weak over time, I crafted a support for above and below the mount to help stiffen up the area around the motor mount. I also uploaded the plywood pieces so anyone else...

These new mounts utilize the existing screws, allowing for a seamless installation process without requiring motor removal or belt loosening. Simply remove one screw at a time, insert the new mount, and reattach the screw while leaving it slightly...

Print two of the short ones for LH XY Motor and two of the tall ones for RH XY motor. These use the existing screws and can be fitted without removing motors or loosening belts. Just remove one screw at a time and insert the new mount and put the...

These mounting brackets are for attaching 28mm (or smaller) hobby/RC brushless outrunner motors to a board, and I personally utilized them in constructing a 2x4 setup with an IMU that hangs from the ceiling and directs itself based on serial commands...

Landing feet for the HGLRC Sector 132 are designed to fit motor mounts for 1106 Motors perfectly. They're low profile, eliminating the need to scratch up bolts on the underside of the drone. These feet add only a negligible ~2 grams to the drone's...

TronXY X5S Adjustable XY Motor Mounts. To assemble, you'll need a M5x15mm screw, nut & washer to tension the belt before tightening and some M3 washers for the motor. Updated 12/23/2017. I corrected issues with the first version. Download the...

I'm having difficulty aligning my lead screws, so I remixed the original Z motor mounts to be able to slide the motors back and forth for alignment. Also removed the lettering on the side, because that is my biggest complaint with the BLV mod. I did...

Motor Mounts for the Turnigy Aerodrive SK3, 3536 size, 1400kV. Incorporates holes for the motor mounting screws. One is 90 Deg angle; the other has 7 Deg tilt off vertical. Print with the motor side (the side with the big hole) flat on the bed. No...

For the Chinese laser engraver: V3 - A generic mount is provided for the gantry drag chains or wire looms on a standard Chinese laser engraving machine, which features smaller chamfers in the corners compared to the NEMA 17 motors found on my...

Additional hardware - 2 Nema 17 stepper motors - 2 Nema 17 right angle mounting brackets - 224mm GT2 timing belt - 20 tooth GT2 pully with 5mm bore - 5mm to 6mm flex motor shaft coupler - Various M3, M4 and M5 screws, nuts and washers - M12 threaded...

V-Core 3 motor mounts (aka FMMM) The name Full Metal Motor Mount (FMMM) is given by RatRig Discord community.for enclosure1 owners please read comments belowNothing fancy but seems useful for some other users.I was not happy how to handle XY Motor...

V-Core 3 motor mounts (aka FMMM) The name Full Metal Motor Mount (FMMM) is given by RatRig Discord community.for enclosure1 owners please read comments belowNothing fancy but seems useful for some other users.I was not happy how to handle XY Motor...

I propose these engine mounts for the TRONXY X8, the original ones are absolutely not straight... ... In case of offset on the X axis, you can decrease or lengthen the motor plate of a few millimetres, I put you the sketchup file so you can modify it.

Discovered the motor mounts on my NIB Eurofighter were poorly adhered to the frame. https://www.rcgroups.com/forums/showpost.php?p=50952911&postcount=1620 Alternate design provides much greater contact area for adhesion to the foam frame. ... ...

My variation on the XY motor mounts and idlers is quite straightforward - beefed up to give a bit more rigidity. For 3030 extrusion, I opted for welded insert nuts instead of standard ones. ...This modification results in a fatter part, so make sure it...

The motor mount is pretty solid as long as it's printed thickly, with walls of at least 5+, I've had good results with PLA and PETG, but ABS would be the best choice. The transmission flip mounts are not as strong, they work but sometimes break...

Flip your 10 ii kit transmission and motor forwards for the best cg! The motor flip mount fits a good range of pinions, 10-14 at least, maybe a bit lower and higher. The motor mount is pretty solid as long as you print it pretty thick, 5+ walls, I've...

These are basic DC motor isolation mounts for use in Athearn Blue Box locomotives or other similar open frame chassis. I designed these around 15mm x 34mm can motors found on eBay. They are similar in dimension to old Sagami or Mishumi can motors. Be...

Nose wheel mount, main gear mount, and motor mounts for use on the FliteTest Explorer RC airplane kit print nose wheel mount with the sloped face down so that no supports are required. The control horn mounts with the control arm down so no support...

Customized version of https://www.thingiverse.com/thing:3234634 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3234634

I 3D modeled two different motor mounts although only one is needed. There is a plain version that lacks any detail and one with detail to better fit in with the model. I used an ELEGOO Mars to print out these pieces in resin. No supports were...

10° Tilted Motor Mounts: - They are labeled with F (Front) and R (Rear). Calibrate your Naze while LEVEL, then add a 10° Pitch Offset via CLI: align_board_pitch = -10 1806 and 2204 Motors are supported. ... Because of the Angle, you might have to...

Designed specifically for the QAV250, 10-degree angle motor mounts can be utilized on other frames as well. Included are the top and bottom components - these should be used to securely sandwich the quadcopter arms with the top and bottom pieces in...

To secure the motor, apply sticky two-sided foam tape on the mount's bottom half excess space. This not only holds it in place but also cushions against harsh vibrations. Drill custom holes (I used 4-40 screws) with a size slightly smaller than the...

Http://www.thingiverse.com/Apps/customizer/run?thing_id=694160 Instructions Using The Following Options: shaftClearanceDiameter Is Set At 8 Diameter Motor Mount Hole 2 Centers At 16 Angle Arm at 110 Degrees motorTilt is set to 12 Degree Diameter Of...

... Updates: 7.11.17 Added one millimeter to motor mounts and spacer to help with clearance for 48mm tall steppers. Also added one millimeter to the spacers. I haven't print-tested yet because I installed Yanick's version with my first modified space.

After receiving my Tronxy X5S, I noticed that the X and Y motor mounts were prone to flexing. In response, I designed these custom mounts to eliminate that flex. They will need additional support since I left a section under the 2020 rail without...

For Trampoline Motors, Set Up on City Streets.

I created these so Prusa MK2 owners could purchase standard 30cm leadscrew motors, available for free, and install them easily without having to wait for the specific 32cm motors that can sometimes be expensive and hard to get. These will get you up...

Boost your print speed with these motor mounts, designed to work seamlessly with ice cream sticks (9.5mm wide, 2mm thick). Printing time is approximately one hour for four mounts. One version features adjustable settings that slide over the stick,...