holosun 510c cover 3d models
153612 3d models found related to holosun 510c cover.thingiverse
This is a protective cover for the Holosun 510C Red/Green Dot reflex sight. It's designed to be a "very snug" fit, so there's little chance of it falling off in transport or field situations. It'll protect your Holosun 510C while not in use. ...
thingiverse
This versatile sight cover protects the Holosun 510 C with rugged efficiency, its utilitarian design masking a practical purpose: safeguarding against scratches and scuffs that come with handling and storing this essential accessory.
thingiverse
This is a TPU material cover for a Holosun 510C series Red Dot rifle sight. The design is made to fit the sight snug so that it will not fall off yet is easy to remove. The TPU material will not mar the finish on the sight. It is printed using...
thingiverse
This is a lens protector housing for a Holosun 510C for airsoft. Use the existing torx screws from the sight to mount this. ...There's a relief on the inside for a 2mm polycarbonate lens.
thingiverse
Pivoting cover for Holosun HS512c red (green, or gold) dot optic.
thingiverse
HOLOSUN HS510C TPU cover from dust and scratch. Easy to put on and off, tight fit. It is printed with supports. ...Layer height 0,2 mm.
thingiverse
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
cults3d
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
Cover for the front of a Holosun 407K/507K reflex sight. This is the side that collects the most dust when holstered and is the hardest to clean. ... UPDATE: Added slots on the side to make it easier to grip when removing/installing.
thingiverse
Update V3 March '23, added side lips for active retention of cover, probably final edit Update V2 March '23, improved clearance between cover and front of glass This is a basic cover I made for my Holosun 508T. I used the dummy model by Disco_Rex,...
thingiverse
A dust cover for a Holosun HS510C Red Dot optic. Other models I tried were too small, I don't know if they were for previous versions but I couldn't get them to fit. Designed a new version from scratch with rear pull tabs. There is a small...
prusaprinters
Cover for the front of a Holosun 407K/507K reflex sight. ...This is the side that collects the most dust when holstered and is the hardest to clean.</p> <p>UPDATE: Added slots on the side to make it easier to grip when removing/installing.</p> <h3>...
prusaprinters
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
I saw there wasn't a cover available online so I made one. ...Print upside down with biggest opening facing up, 100% infill.
cgtrader
Compatible with all weapons. ...Compatible with plug-in system.
thingiverse
Dust cover for the Holosun 407 and 507 v2. Also added easy on/off handles, cutout for the buttons, cutout for the battery tray, and cutout for the solar. ... Recommend reducing contact Z distance as much as possible to improve support quality.
thingiverse
This is a remix of the original cover user jcharouz created this addition only includes the short cover with an added cut out for the battery compartment. ... Link to jcharouz: https://www.thingiverse.com/thing:4380879
thingiverse
I added a lanyard hole so I can attach a flag or something, making it easier to stow the cover in pocket temporarily when I remove it to shoot.Printed mine with TPU with its natural orientation (opening facing down) with supports, so I could iron the...
thingiverse
Remix to cut out the battery door, relieve the bottom for the M&P slide profile, and added a little nub to increase retention when using TPU.
prusaprinters
I needed a cover for my new Holosun SCS-MOS sight on my Glock - and there was none to be found...This is designed for my Glock 21 Gen.5, so the slide might be wider than on your Glock.Print in an flexible material, I used TPU. There are two little...
thingiverse
I needed a cover for my new Holosun SCS-MOS sight on my Glock - and there was none to be found... This is designed for my Glock 21 Gen.5, so the slide might be wider than on your Glock. Print in an flexible material, I used TPU. There are two...
grabcad
The Mazak Nexus 510C-II model utilizes the Model Edgecam postprocessor, which is available at http://exinterconsulting.webs.com/. ...This postprocessor enhances the functionality and efficiency of the machine.
sketchfab
Holosun HS403R scope 3d model Archive contains FBX and Unreal Engine 4 texture pack
thingiverse
Hey guys, I just made an Reddot cover that fits my Holosun HS503G smoothly. Since my AR is an Spartan version i added a random Spartan helmet to it, but also added a clean version. The inner diameter is 29mm so you could adjust your print to your...
thingiverse
This is my attempt at modeling the Holosun 508t v2 RMR. It's not perfect and has no branding on it. Might need to be filed down on the front side to fit your weapon (I had to for mine). ...Have fun!
prusaprinters
This is a mount for the Holosun 509T pattern of micro optics. It's designed to use 30mm M3 hex head capped screws and hex nuts. </p><p>I've tested printing this with up to a 0.6 nozzle and 0.2 layer height- smaller nozzles and layers will work...
prusaprinters
This is my attempt at modeling the Holosun 508t v2 RMR. It's not perfect and has no branding on it. Might need to be filed down on the front side to fit your weapon (I had to for mine). ...Have fun!</p> <h3>Post-Printing</h3> <p...