holley terminator 3 5 screen mount ez support by 3d models

This remix is designed for the Nextion 3.5 inches touch screen NX4832T035. The knob used in this project can be found at https://www.thingiverse.com/thing:2974058. To make modifications, I added a Fusion file (.f3d). I hope you enjoy printing and...

This is a high-quality camera mount designed specifically for use with Creality Ender-3 and RasPiCam in conjunction with Octoprint and Timelapses. It offers significantly enhanced durability and security when mounted. After trying numerous different...

This is a Custom Case designed specifically for use with a 3.5" TFT LCD display on a Raspberry Pi system.\n\nThe case has been engineered to work seamlessly with the following Raspberry Pi models:\nRaspberry Pi 3 Model B and beyond\nRaspberry Pi 2...

Remix for a RPi 4 with a GPIO 3.5 cheap screen. I'm printing this for now but working on a remix of this with a 30mm cooler and better color filament :P I modified also the slot for the board because it was too tight. Edit: Added another...

I noticed that the screen has become out of stock and was removed by the seller from Amazon in the US, but it's still available from the manufacturer and internationally: https://osoyoo.com/2019/09/20/instruction-for-raspberry-pi-5-dsi-touch-screen/...

The parts needed for this modification are: - 8 m3 screw 12mm - OSOYOO - Display touch screen LCD 3,5...

This is the RAM EZ on/off base mount for the handlebar and its rubber adapter. ... You can print the base in PLA or PLA carbon fiber (better and stronger) and the adapter with TPU.

Remix for a RPi 4 with a GPIO 3.5 cheap screen. I'm printing this for now but working on a remix of this with a 30mm cooler and better color filament :P I modified also the slot for the board because it was too tight. Edit: Added another version...

I recently acquired a counterfeit 3.5 inch display for my Pi 3B, and I was less than thrilled with the selection of cases available for it. So, I decided to take matters into my own hands and design my own custom case. ...To do this, I modified the top...

Upgrade your FT-5's front panel seamlessly by installing a new full-screen graphics display - it's an effortless swap that gets you up and running with a crisp, high-resolution interface in no time.

Cover for 3.5" LCD-TFT BIGTREETECH Touch Screen [E3 edition] and 20x40 extruded aluminum bars --------------------- Caution! Only slender USB sticks enter the display - Printing must be paused twice to insert four M3 nuts inside. - The reset button...

Chitu FDM Plus 3D Printer Controller Case for 3.5 Inch Touchscreen Display

Created for my Voron Switchwire

I purchased a 5 Inch Capacitive Touch Screen HDMI LCD Display for my Raspberry Pi, but the included case didn't meet my expectations and the way it attached to the raspberry wasn't satisfactory. ...I therefore decided to build my own custom case,...

... running octoprint on a raspberry pi 4 with a 5'' touchscreen. The holder is fitted to the screen an Pi, so that they don't need additional fixation. But it is possible to use some "PC screw extensions" to mount the electronics to the backside frame.

This mounts a Waveshare 4.3 inch DSI LCD with a Raspberry Pi3B+ inside an Ender 5S1 in the original screen mount location. It's quite likely to also work with a Pi4, but I haven't checked. Once Klipper is installed on this printer, the old...

Print Settings: Printer: Anet A2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 25% Notes: I printed this design with 5 walls to ensure the holes and straight walls were fully infilled, as they are designed to flex. Supports are...

Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 25% Notes: I printed this with 5 walls to ensure the holes and straight walls were basically 100% infilled, as they are designed to flex. Supports are...

Two M4 threaded nuts are required, along with two M4x12 screws. ...Additionally, one Ender 3 LCD display unit, complete with mounting screws, is necessary. ...Furthermore, two LCD cables will need to be procured for this project.

This is a mount to allow you to put a BTT TFT35 v3.0.1 screen in the Ender 5 Plus. It is slightly recessed so that you don't have to cut a notch in the opening for the dial. Have not tested a print yet. Simply printed the original and noticed some...

Print sony-a6300-lcd-screen-shader_v1.stl with flexibility (TPU or Cheeta) and sony-a6300-lcd-screen-shader-solid_v1.stl in strong PLA material. Next, slip the flexible piece over the solid PLA part, then secure the flexible holder onto the LCD...

Screen Frame T Joint is designed specifically for a 5/16 x 3/4 Aluminum Screen Frame. To bring this project to life, select the Print Settings that will take it from concept to reality. ...The key setting to focus on is Infill: at 0.95.

Two side mount and the spacer/washer for mount to the frame print 4x of it

Front panel replacement for the FT-5 to use the Full Screen Graphics display. ...Nice drop in replacement.</p> Category: 3D Printer Parts

This set of files allows you to mount the BigTreeTech / BIQU TFT35 onto the front of your Ender 5 or Anycubic Chiron printer. BE AWARE! The reset button on this screen is at the bottom right corner. Pay attention when super-gluing the mounts on the...

This set of files will allow you to mount the BigTreeTech / BIQU TFT35 onto the front of your Ender 5 or an Anycubic Chiron printer. BE AWARE! The reset button on this screen is at the BOTTOM RIGHT corner. Pay attention when super-gluing the mounts...

This is a DUMMY-MODEL of an OPEN-SMART module, so don't expect to have a working touch screen model after printing this... Should be powder bed... ... But for real it may come in handy to design a case for your electronics project.

Easily mount it on walls, hang it upside down, or simply place it on your workspace, thanks to the conveniently located mounting holes underneath.Enhance the longevity of your setup with a recommended fan filter, available here:...

A BTT-TFT35 screen mount with access to usb pot. to use this, you will need to cut a section from you standard electronics box.. ...modify at your our risk!