holley sniper efi screen mount 3d models

... in my 1965 Mustang. ...I decided to column mount the sniper screen and cover the dummy oil light area that isn't wired up. I am running another oil pressure gauge and tach on a shelby style center dash pod. ... The diameter of the column shaft is 2.25"

Holley Sniper screen mount for 2.25" steering column.

First design of Holley Sniper LCD 3.5" screen mount This is to hold the Sniper screen, will be uploading a remix down the track with hinge to fold away. ... Have not yet printed my own, but dimensions should be accurate.

This case holds the Holley EFI Terminator X 3.5" screen. Requires m3 countersunk hardware for mounting and installing the face plate. ... Added a flat cover per request.

i dont have a provision for it so i use it for under hood or cowl temps for my Holley EFi terminator, HP, Dominator. ... This isn't 100% the ap is 3/8 NPT but the bore is too large to thread properly, i ended up just threading the sensor in untill it...

This is a dust cover for unused Holley efi connectors. It will fit J2b, J3, J4 connectors. It has a friction fit and will not fall off if mounted with the connectors facing down. ...Follow me on instagram at South Florida Muscle Cars

This is a custom-designed screen mount specifically engineered for the Holley Terminator 3.5-inch display screen. The innovative design features a dedicated slot to accommodate a standard worm gear hose clamp, ensuring secure and convenient...

I needed a way to mount the 7" Holley digital dash screen to my Cobra. I had been using the 3.5" handheld screen mounted to a Ram ball mount, so I reused that bolt pattern for the screen bezel and the dash mount. The baseplate has multiple holes...

Just a model of the Holley 3.5" handheld mount. Been working on a pillar mount version so I figured I would upload models as I go. ...You will have to add your own felt sliders to the back, but other than that, it should be a perfect fit.

More Mounting options for the 3.5" Holley Screen

Insert for injector connectors on the Holley Sniper EFI units to hold electrical terminals in place NOT GUARANTEED TO FIT, STILL TEST FITTING

Remover hose clamp mount, made flat mount with 6mm holes

... printed this in PETG on an Ender V2 with 235 Nozzle Temp and 75 bed temp on its back. ...If need be add your own mounting fixture and print to your needs. Was disappointed when I bought a 1k EFI system and it didn't come with a way to mount the screen.

I have not been able to test it yet.94 - 2002 Trans Am Terminator X Screen Mount that covers vent. It is contoured to match the dash. There is a non-angled version and an angled version that faces the driver better.Parts needed to complete...

This will allow you to mount your Holley Terminator or Sniper3.5in screen into a 52mm gauge hole

Mount plate for Pro EFI 4" can display. ... Attaches to RAM mounts

This replaces the factory radio with a mount for a Holley Terminator or Sniper 3.5" handheld. The holes for the mounting tabs have to be drilled. The handheld slides in from the top and has a friction fit like the factory Holley mount. ...There isn't...

version 1 of the 12" holley display mount

International Scout 2 2bbl Holley Sniper 2300 air cleaner adapter. This allows the use of the stock 2bbl air cleaner onto the Holley Sniper 2300 throttle body. Has recesses for stock air cleaner gasket, etc. ... Suggest PETG or other high temperature...

... less Use loctite GREEN on the sensor nut AFTER you get the proper airgap. Holley setup = 5th tooth digital falling 2 versions : factory alignment and centered which moves the sensor toward the timing cover 3/32" ABS or higher temp recommended.

-Cleared out the reverse side of the hose clamp slot for printers with difficult breakaway supports EG stratasys. -Added additional wire bend clearance on reverse -Other measurements and fillets to taste -Added gauge pods - either glue-on if...

Holley Terminator X 3.5" display steering column mount. This is designed to fit 4" steering columns. I used this in a 1970 Nova. ... Additional Parts Needed: (2) M8x1.25x75 socket cap screw (allen head) bolt (2) M8x1.25 nylock nuts 1/2" wide...

Adapts stock intake manifold to a Holley sniper EFI

... kit features a throttle body and manifold with a 99% accurate model. ...The intake and exhaust flange dimensions are precise, while the MAP sensor is mounted on a recommended 4" length of tube. ...Note that this product is for mounting solutions only.

Customized version of https://www.thingiverse.com/thing:52734 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=52734

the inner diameter of the mount is 27mm so it should fit most sniper barrels. lmk any improvements, questions or different sizes you may want in the comments and I will get back to you as soon as I can! Thanks! ... 22mm inner diameter now...

... and Functionality. Crafted from High-Quality Printed TPU, it boasts Unparalleled Strength and Durability. Whether you're flying through Treacherous Terrain or Cruising through Open Skies, this robust mount keeps your antenna securely in place.

This premium mount is made from high-quality TPU that offers exceptional durability and maximum strength, ensuring it can withstand even the most demanding flight conditions. Crafted with precision, this GoPro Mount has been redesigned to optimize...