hold open hinge 3d models

 I have opened a feature request for this.  Here's what the circular nozzle “landing mark” from an inner scarf seam (inner-outer-inner wall order) looks like, for reference: What about setting xxxxxx ?Use of Conditional Scarf Joint is strongly...

I wanted to wire tie the mount to the shelf (as I have done with the printers).The link below is to the USB cable.Amazon Basics USB 3.0 Extension Cable - A-Male to A-Female Adapter Cord - 3.3 Feet (1 Meter) -...

Flow-mode follows in the next update. Additional Hardware required for Node-RED & Alexa Any device that runs Node-RED, examples would be: (recommended) Raspberry Pi Any Linux machine (instructions are provided for linux) Any Windows machine ...

---- ###Some of My Designs Click an image below (opens in a new tab) or go to my designs page and see them all. If you see some thing that you like , **please click the Like button** and turn that heart red . ... <div><a rel="nofollow"...

Flow rates were getting so high that the nozzle started to impede flow, an open nozzle is now uploaded 6/25/2021 stronger servo mount on part inlet duct 6/30/2021 improved motor cooling impeller, larger fins, improved filleting, removed thin shroud,...

I cut out a tight opening so that a shelf sleeve can just go through out of some cardboard, and then I put blue painters tape over the hole (and over the edge of the sleeve) and with a very sharp razor-knife I remove the inside of the tape leaving...

If you don’t have any plugs for the 9V battery, you might just safely open an old battery to remove the connection and use it as a plug for your circuit. Doing so you now can solder the corresponding wires to the plug. Use heat shrink tube and...

This Bong is constructed much like the other, but with the following very important differences: -It's input an output are open to the external environment -The cone-cap on the top of the left bong has two functions. To prevent stuff falling in and...

Game Tokens - large and small!&nbsp;&nbsp;For use in your next wargame!No supports are required.Grooved backside to facilitate easy grip even when soaked in the blood of your enemies.Plain-backed version for those unconcerned with being soaked in the...

&nbsp;To date, I have measured maximums of 1.25 PSI (output throttled) and 11 CFM (output open) with a two-stage build at about 4300 RPM. &nbsp;As a bonus, it is fairly resistant to damage from inhaled debris, not that I recommend chucking stuff in...

It is extremely easy to make models for dual extrusion (assuming I am doing it right) Just take the parts you want in your second stl, group them, duplicate it, turn it into holes, and then group the holes with the objects for your first stl. If you...

The open part of the Belt Holder should be facing to the right (towards the Z extrusion).Slide the belt over the Y motor pulley.Install the Y Idler using the M3x20mm screws and tighten the belt.Reinstall the heated bed using the tiny Torx...

Use for scatter terrain, on your model railroad, in a diorama, or whatever gets your motor running.Two sizes are included within the files.&nbsp;A small area of the power turbine need supports (see images).Easily resized.&nbsp;Designed on...

Here you are!Designed for use with “Way Basics Eco Stackable Storage Cube, Cubby Organizer (Tool-Free Assembly and Uniquely Crafted from Sustainable Non Toxic zBoard paperboard), White”...

Feel free to do whatever you want with them.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

You need to open that single layer adter printing for the screws.Assembly instuctions:I won't explain every detail here, since if you build it you'll know that printer well enough for that. Also you can look up details in the 3d Models.</p><p>The...

https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction&nbsp;Use with your Armoured Shelter https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models &nbsp;or carry with the Machina to their...

Note the treads match in shape the body of the Freight Ten.Superglue the cab superstructure to the body to the front grill is overhanging the front slightly (see the images).No print supports are needed.Superglue works best for gluing it together.Did...

More cargo for all of you Sci Fy tread heads out there.Freight Ten https://www.prusaprinters.org/prints/134117-freight-ten-cargo-transport-model-science-fiction&nbsp;Transport your Armoured Shelter...

Change if you are using something else (trying to use up what I bought a few months ago.&nbsp;Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Set your alarm clock and bang out 3 of these a day (per printer)!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

3) from the PC, open the application you usually use for flashing Marlin firmware. 4) plug a USB cable from the PC to the mainboard's USB port and connect the application to the printer 5) follow the instructions provided by your application to...

For additional details, see the Using Fonts and Styles section on the following page: https://en.m.wikibooks.org/wiki/OpenSCAD_User_Manual/Text ---- ###Some of My Designs Click an image below (opens in a new tab) or go to my designs page and see...

(see the images).Superglue the nose to the body (see the images).Superglue the top deck.Leave the main gun to swing freely.Print supports only on the arches of the nose (that's how I printed it, it might print ok without them).Superglue works best...

Ensures that the exterior is exactly 4 perimeters, and the diffuser is exactly 2 perimeters) Perimeters: .45mm Infill/Perimeters overlap: 25% You can customize openings by adjusting/adding/removing the included modifier on the base. (keep in mind...

The 3D printing model's chosen scale is 1/400 for FFF/FDM version and 1/800 for DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 128 parts;- A printed ship without the platform is 210 mm tall, 412 mm wide, 644 mm...

---- ###Some of My Designs Click an image below (opens in a new tab) or go to my designs page and see them all. If you see some thing that you like , **please click the Like button** and turn that heart red . ... <div><a rel="nofollow"...

Much of that comes from off world crates.Build!&nbsp;Get back in the Fight!Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Four sizes - large to small.Lumber stackFour pieces of loose lumberStack or glue, make a...

https://www.prusaprinters.org/prints/132133-machina-robot-model-v3&nbsp;Also great for use to guard your Armoured Shelter ( https://www.prusaprinters.org/prints/121033-armoured-shelter-terrain-two-models ) Lol!Designed on Tinkercad.Four parts to...

So these process towers were built and deployed to slowly refine the lost minerals and deadly toxins within the atmosphere that have value, instead of allowing them to go to waste within the short lives of the damned, I mean worker's lungs…Print with...