hit miss model engine

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... DonationsIf you found this print helpful, sending me a...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

If your name is not Matt, then there is a template attached in the model files called “Name_Plate_Template”. If you wish to add your own name to this template, open the attached file called <code>Name_Plate_Template.step</code> in a CAD software of...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

To split it with ease, right-click on your model within Cura. When preparing your parts for printing, make sure flat sides are aligned downward. For a smoother print process, consider setting 0.1mm layer height and 40% infill as defaults. Here is...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

 **Additional part sources** --- * [The Tensioner knob is a remix of donnyb99's CR-10 tensioner](https://www.thingiverse.com/thing:2168903/files) * [The tensioner itself was inspired by mukha521's AM8 tensioner but...

&nbsp;On my ESC I have to start with the minimum setting (effectively the throttle channel on an RC model), which I believe is a great safety feature. &nbsp;BTW you can also program your ESC using the knob as if it was a throttle control, if your...

... top layers and tops. but the latest models are off course the best. Please share your towers so I can see how colorful and tall you can make them. ... And don't forget to check out my Instagram: fredslund3d Good Luck & Happy Printing!

This is then seen when viewing the seam around the edge of the keyfob - everything should line up, with the flag the correct way up when viewed with the keyring hole on the left-hand side.Building the layer cake...Drawing the Union Jack - In the...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

Once you have the rights % size change, you can Meshmixer or TinkerCad any model onto the clip_in_insert to create all kinds of new experiences for your animals, or useful things such as a cover for a feeding area to prevent gunk from falling into...

Happy soldering! Source Files This print was modelled in Onshape. You can access the source files from here:</p> <ul> <li><a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I considered adjusting the model, but decided to leave it as is. I'd rather have a more positive engagement that you can adjust to your liking, than end up with one that doesn't latch in place securely enough. ;)</p><p>I will leave this marked as a...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...

Min of 190mm build volume Full print parts head on over to cults: https://cults3d.com/en/3d-model/various/scx6-trailer Can be setup as single or dual wheel. Dual wheel requires a min of 190mm. ** UPDATED parts ** 2022/02/10 - S Hook - to be...

Using a allen key also has a couple of smaller advantages, those being reducing the number of pieces in the model, while also providing the added benefit of acting as a keychain mount.The gadget is made up of a few common parts apart from the printed...

Durch die strukturierte Beschichtung erhält das gedruckten Modell auf der Unterseite einen schönen, strukturierten Look. Je nach Bedarf kann nun zwischen glatter oder strukturierter Oberfläche gewählt werden. Rändelmutter M3 / Große...

:DI put 3 holes in the top of the soap container where you can store your toothbrush or similar bathroom itemsI hope you enjoy the model and just try it out for yourself.I have written a description of how to make the soap here, which should give you...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

The files are prefixed with Updated_ or New_.Here are a couple videos of it running  Please refer to the Original model for assembly and any other sources.I have uploaded the file as a Fusion 360 archive folder so you will need Fusion 360, Fusion 360...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

If there’s a flat-ish STL model that you like, you can load both this and that stl into Cura, scale and move them around as needed, and slice: Cura automatically joins models where they overlap. There’s also an insert plate that fits inside style0,...

Enable the "Generate Support" setting **PrusaSlicer** Load the model as a multi-part object into PrusaSlicer. Then perform the following actions, as in the screenshot: 1. Set the supports to Support Enforcers Only 2. Right click on the rectangle...

--- # Assembly ## Key Switch The key switch is a two-terminal model (aka, it only has "on" and "off" modes for simplicity) intended for generic Chinese electric scooter ignition. It is intended for a through-hole of ~10mm. I made it 11mm to account...

If there is too little filament on the coil, it is pointless to print a large model. And it's a pity to throw away the leftovers, too. But you can print such a trinket as a gift or just for your own pleasure. P.S. When printing this model, not a...