high heel model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

If there is too little filament on the coil, it is pointless to print a large model. And it's a pity to throw away the leftovers, too. But you can print such a trinket as a gift or just for your own pleasure. P.S. When printing this model, not a...

Enable the "Generate Support" setting **PrusaSlicer** Load the model as a multi-part object into PrusaSlicer. Then perform the following actions, as in the screenshot: 1. Set the supports to Support Enforcers Only 2. Right click on the rectangle...

You may not be able to fit 3D printed indicator-mirror holder perfectly between brake lever and different shifter model.Ningbo Jietong Electronics • E751 (MIRS-201)2 x Amber color LED for left and right turn indicators.These switches are more...

 When you slice the model for your printer, check a few crucial layers to make sure that the bolt holes and nut slots leave enough wall thickness everywhere.A note about the coordinate system:  The enclosure is modelled on it's left side,...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

They should snap into position once you're close enough.25.Finally top of the “Prusadusa and the sands of time” clock by glueing the Prusadusa model onto the central pin sticking out of the cone in the middle. This is now your seconds...

--- # Assembly ## Key Switch The key switch is a two-terminal model (aka, it only has "on" and "off" modes for simplicity) intended for generic Chinese electric scooter ignition. It is intended for a through-hole of ~10mm. I made it 11mm to account...

On one of the two lower enclosures in my 2x2 stack, I mounted the spool holder low enough that the door of the enclosure above could swing over it, but I mounted the other one a bit too high. Rather than remove and remount it (possibly leaving a...

Super easy customizer for creating bolts, nuts, washers, threaded rods, and standoffs.Features:easier than other thread customizers, just pick a thread and configure details950 threadsfive types of bolt heads : standard, cheese, countersunk, round,...

If it still does not work, then I recommend performing a more detailed bed level correction: https://help.prusa3d.com/en/article/bed-level-correction_2267.I highly recommend choosing two different shades of color for printing 12 of each shade. So the...

Crafted with precision and finesse, this high-tech tool serves as both a symbol of hope and a formidable defense mechanism against the forces of evil that threaten the city of Tijuana. Equipped with advanced sensors and propulsion systems, the...

So _1_6_10_7 is 1:600000000 or one in 60 million. The accuracy of the model The model was made taken these features as literal from the book: The spaceship was a cylinder 50km long and 20km in diameter, although it can be expected aliens having...

 I know of only one 3D modeling tool where that is possible - without requiring that each user become an expert in 3D modeling.  That tool is OpenSCAD.  OpenSCAD has a "Customizer" feature that allows users to provide input to an...

You don’t want them pulled too tight. Install the Chain Link Cover Clips onto the drag chain links to close the chain. Slide the Cover pieces into place over the Chain Frame Mount and the Drag Chain Arm Connector.Edit 2021/08/07: Added Genius...

10 - 15W)Sample links:Power Cable Lamp Socket with Switch E27   -   https://www.amazon.de/dp/B00P2DV2NY/ref=pe_3044161_189395811_TE_SCE_3p_dp_1?th=13 - 12 W E27 LED Light Bulb Corn Light   -...

============================ Das Modell hat keine geschützten Propeller und je nach Motorisierung liegen hier bis zu ca. 3 KW Leistung an. So viel Leistung kann großen Schaden anrichten. Immer entsprechende Sicherheitsvorkehrungen treffen und nicht...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

This is a model and instructions for how to build your own fiber optic light engine that is smart and can be controlled through google home. This version uses a smart LED light bulb as the source of light. It can use any smart light bulb that is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W*.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

We don't use the shell.PrintingPrint all models in their original orientations.The parts should be printed with support. Try tree support as it wastes less plastic and is easier to remove in one go.</p><p>I printed my parts in a black/red color...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

&nbsp;Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

You might also want to clean it with alcohol or antibacterial soap, on occasion, depending on your preference.While this design is Creative Commons - Attribution, I would ask that anyone who wants to sell this to other people take all precautions...

This set collects a number of fantasy character models and makes them available for use in Pocket-Tactics. This set doesn't represent a specific faction, just a number of loose pieces to use in your own custom builds, either keeping within this...