hide wyze cam 3d models

This mount This Wyze Cam mount was based on the mount made by cool3dp but doesnt need any extra screws, it attaches to the two bolts on the front left. ... Already tested and ready to go.

Simple remix of quincyicq's Wyze Cam mount for the Ender 3: https://www.thingiverse.com/thing:4518643 This should work with any 3D printer that has v-slot rails on the side.

I took the Wyze cam offset mount front bar by Cerabus but needed if for the front 202 extrusion of my CR-10 v2. ...I modified the length so it would clear the bed when its fully forward.

Simple Window and Wall mount for the Wyze cam V2. ...Parts needed, cable tie for cable management and screws or suction cups to mount to the window or wall.

Wyze Cam Pan mount that uses the plug itself as a mounting point, so no drilling required! ...The camera itself is lightweight enough so the plug itself should support the entire setup just fine.

Remix of Foden7's Wyze Cam v3 siding mount (https://www.thingiverse.com/thing:4838459) because I needed the camera to be angled ~30 degrees to the right so it was better aimed at my front door.

Cover for Wyze cam v2 (maybe others) to help reduce reflections when placed facing out a window. Reduced back so it can print face down without support. ...Added wider face to block reflections.

The Wyze mount point is not the full size of the Wyze Cam V2 base, and does not need to be (it is snug!) - this allows you to print this much faster without support. You can slide the cam back and forth with a little force to put the camera closer...

I needed something to tilt my Wyze Cam Pan down a little bit so I designed this inclined holder. It comes with two version, with or without the shoehorn holder. ...Enjoy!

This also allows you to tweak the angle of the camera to your liking on the mount since the Wyze Cam can move on its base.The Wyze mount point is not the full size of the Wyze Cam V2 base, and does not need to be (it is snug!) - this allows you to...

Cover for Wyze cam v2 (maybe others) to help reduce reflections when placed facing out a window.Reduced back so it can print face down without support. ...Added wider face to block reflections.</p>

This isn't so much a remix per se, but I adapted Zachary's Wyze Cam V2 Mount from https://www.thingiverse.com/thing:5643563 to create a V2 mount that would snap fit onto one of the support poles (approximate diameter of 15.95 mm) of my Creality...

... my 3D printer. Please see the original designer's design for the additional parts which is needed to attach this Wyze Cam mount to. ... I listed the Printer Model as CR-10 since the CR6-SE was not listed as the "printer used" in Thingiverse menu.

... to poke holes in my firewall for remote viewing or use my VPN. Adam Argo details the process of turning the WyzeCam into an OctoPrint Timelapse camera here https://medium.com/@adamargo/using-a-wyze-cam-with-octoprint-on-a-raspberry-pi-7a1c886b9afe

After I printed and installed the awesome Prusa Mini Base by David Warboss I was unable to use the Wyze cam mount for Prusa Mini - Bottom Cut Flat by&nbsp;With_Maltodextrin so, I set out to find a way I could make it work.This is my current solution,...

This is a 3D printed cover designed to shield the Wyze Cam V.2 from the elements. It's not explicitly stated whether this protective casing would also be suitable for the Wyze Pan model. The two available designs feature either a flat or pointed...

Ideal for those who have an older Wyze Cam V2 or V3 already mounted to the celling exactly where they want it, and wish to use the micro-USB cable already there (however you may want to swap the older USB power brick to the Pan Cam v3's power...

This file includes only the Wyze Cam adapter component.\r\n\r\nTo bring this adapter to life, you'll need to print parts from the design linked here:\r\nArticulating Mount.\r\nhttps://www.thingiverse.com/thing:2448971\r\n\r\nPrint as many arms and...

... very snug in a standard single gang outlet box. I have mine installed with no other hardware (screws), just pressure fit. If you are looking for the version of this thing that works with the Wyze Cam v2: https://www.thingiverse.com/thing:4139309

This Wyze Ender 5 Modular Mount is a combination of HeyVye's Modular Mounting System and 2 parts I designed myself to mount the Wyze Cam V2 on the Ender 5. The clip was from a GoPro mount I redesigned(the original didn't work at all so I rebuit it...

The Wyze cams came with plates and magnets to mount them securely, but the pan had no mounting hardware whatsoever. I decided to create a custom mount to hang the camera from a small shelf on the wall. I drilled four holes in the back for attaching...

This Wyze Ender 5 Modular Mount is a combination of HeyVye's Modular Mounting System and 2 parts I designed myself to mount the Wyze Cam V2 on the Ender 5. The clip was from a GoPro mount I redesigned(the original didn't work at all so I rebuit it...

... filament if it doesn't fit. 2. The wyze webcam monitor stand. I did not need supports for this print. Instructions to turn your Wyze Cam into a webcam: https://wyzelabs.zendesk.com/hc/en-us/articles/360041605111-Webcam-Firmware-Instructions

I used these guides for setting up my wyze cam and this cable to connect to my raspberry pi running octoprint: https://community.octoprint.org/t/new-firmware-for-wyze-convert-to-webcam/17761/3...

... when my cases were running out. ...So Figure since a wyze cam is small I would make a small bracket to hold a cam so I could monitor my case level on my tablet or phone. ...I have made 3 different versions of this mount I am currently using V3.

I required clips to keep my Wyze Cam tidy on my Monoprice Mini 3D Printer. It easily secures in place with the printer's existing screws, ensuring a clean and organized workspace. ...This simple solution keeps the cord neatly tucked away, making it easy...

This is a remix of the excellent "Wyze Cam Prusa Mount" by Gabe. I just mirrored it to use it on the left side of the Prusa mini and removed some of the material to make it lighter. Print instructionsPrinted as oriented in the 3mf file.

I made this to add a Wyze Cam to my Seestar S50. Didn't want to mount it on the camera side, to prevent extra weight on the gears. ...The idea is to give the user a look at the sky (for clouds), and to save time, when you can't see your target and it's...

After printing in white, simply enlarge the small screw hole to be slightly smaller than the screw attaching the Wyze Cam v3 to the floodlight body. now slip the printed part into its place and screw in. ... you can simply set 2 cameras on the mount or...

I desired a bed mount for a Wyze cam to facilitate the creation of time-lapse videos. My aim was to avoid adjusting the bed levelers and to have the flexibility to relocate it as needed during printing. ...ABS was chosen for its rigidity and heat...