hglrc m80 pro gps 3d models
92612 3d models found related to hglrc m80 pro gps.
thingiverse
Quadmula Siren F3 GPS front mount for HGLRC Mini10 GPS / crash save, nothing sticking out. make your Sirn F3 a great explorer Easy to print and have gps (considering you have O3 and you don't need any extra cam) Tested : 24 satellites ! ... check and...
thingiverse
Quadmula Siren F5 GPS front mount for HGLRC Mini10 GPS / crash save, nothing sticking out. ...Easy to print and have gps (considering you have O3 and you don't need any extra cam)Tested : 24 satellites !Check and follow my FPV insta for videos
thingiverse
Rear mount for the newer HGLRC M100 mini GPS module, Designed for the Martian II frame. V3 now includes an antenna mount for ExpressLRS. If you don't require this though, it can be easily cut off. ...
thingiverse
Provides foundation for a SMA connector and two radio receiver wire antennas (in 4mm air hoses/pneumatic tubings) as well as protected housing for a GPS or radio receiver. Additionally the screw holes can house said 4mm tubings for roll-over...
thingiverse
This is a rear mount for the Matek M8Q GPS to an HGLRC Wind 6 frame. It is set up for a resin printer and includes built in supports. It fits the standard M3 bolts and has space for M3 washers to avoid crushing the plastic. It is designed to...
thingiverse
A compact platform to securely attach a GoPro Hero 3 Plus camera to a sturdy Batman 220 frame designed by HGLRC.
thingiverse
Modified gps mount for Rekon 5 mini longrange for BN220 gps module and mount for 18X17 beeper
thingiverse
A Simple Case for the Smok Cartridge Holder. This Can Be Improved Anytime^^. ... Print Settings: Printer: CTC Printer Rafts: Do Not Need To Be Used Supports: Not Required Infill: Set to 30 Percent
thingiverse
A simple GPS magnet support for HEQ5 Pro, connected on rpi 4 with stellarmate.
thingiverse
I have remixed this to fit the M100-5883 GPS Module from HGLRC. ... This is for the Rekon 7 Pro FPV drone2 Options: with or without Immortal Tee Antenna Mount
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/lP9aC9Zjf5G
thingiverse
This mount is for the hglrc 100mini gps, to mount it on front of the Flywoo Explorer LR4. ... Print in TPU with 15% infill.
thingiverse
GPS mount designed specifically for the DJI A2 flight controller GPS Pro Plus Puck.
thingiverse
Mounting a GPS device and a GoPro Hero 5/6/7 to the HGLRC Batman 220 is essential for capturing precise location data and immersive video footage during aerial adventures. This specially designed mount securely attaches to the drone's frame,...
thingiverse
A FPV camera mount that fits in replacement of the stock go-pro mount on the sector 5 v3 Printing: Use TPU settings may vary
thingiverse
The GPS module itself comes from HGLRC, but this design should also accommodate other modules measuring approximately 20x22 mm when wrapped in heat-shrink tubing. Two variations of this part are available: one that includes the GPS mount and...
thingiverse
This geotagger unit receives GPS data from a u-blox M8n and sends it to the Flir Vue Pro, enabling automatic embedded geotags. The case securely holds the board via double-sided tape while allowing easy access if needed. The board can be powered...
thingiverse
Took the source GPS one prints merged them with DJI antenna on Windows 3D Builder, Hey, it works! Might need to cut open slits to the antenna and open all the way on the end for the antenna or modify your top plate. ...The antenna can also go from the...
thingiverse
PRINT AS support for GRL_gps Beitan220 or tbs SMA antenna and RX ImmortalT IG @clicknciak
grabcad
Model of DJI - A3 - GPS-Compass PRO prepared for needs of Sevendof AS for development purpose due to lack of officially released of the geometry by DJI.Released with employer permission under Apache 2.0 License.The model includes the DJI Logo and...
thingiverse
Once you have the necessary hardware, use them to attach the GPS module inside its holder, taking care not to block any air vents or other critical components. It's essential to align the GPS module precisely within its housing to avoid any...
thingiverse
I'm running a series of tests on an ATM mount designed to support multiple GPS devices: the BN-180, the BN-220, and the HGLRC M8N, along with a SMA connector, all optimized for use with the TBS Source One V0.2. ...Other configurations should also be...