hex bit storage 3d models

Hex Bit Storage, Holds 70 bits in a convenient small foot print perfect for a tool box

Hex bit storage case (up to 32pcs + adapter). ... External parts (not for printing): 3x70mm wire (rotation axis).

... place for hand screwdriver. ...I used hex H6 bit for screwdriver holder into box. The hex bit is only pushed to the center of the box. It will hold the screwdriver. My inspiration is hier: Hex Bit Storage Box for 1/4" Hex Bits by 3Dizain - Thingiverse

***Euer Schmelz freund*** Hex Bit Storage Box ***would scale to 103% Storage Box*** Make sure you have good bed-adhesion. You can use a brim to be safe. Use 0.16 mm layer height for printing. No supports required. ***ich würde auf 103% skalieren...

English (Deutsche Beschreibung siehe unten)I offer the hex-bit-storage in several variations:This version offers room for 7 x 3 bits onlyOther variants are:8 x 3 bits only8 x 3 bits plus Wera RapidaptorAll variants offer additional options...

Hex bit storage box for ikea skadis board 0.16 support +

Optimze the fitting to your needs by adjusting the scale factor in your slicer.If you have found the right scale factor that suits you, then apply it to all prints on all dimensions (including z) - even on the french cleat holder, so the width and...

... however I am very happy with the end result. The purpose of this model was to create a storage container with the Hex Bit holder found here: https://www.thingiverse.com/thing:4287182 There is a photo showing the hex bit holder inside the box above.

Small capsule for storing 1/4" hex bits. ...Fits 12 bits nicely.

My printer is less well dialed in, so i wanted a bit storage box that allowed more tolerances and still hold my bits. Changes added when remixing: - The 6.35mm(1/4") version needed some rearranging since hex slots became too wide for the cover. -...

Wanted a way to organize some hex bits on my pegboard, couldn't find anything that was exactly what I wanted.  I love the interchangable pegs on RyukyuD's Modular Tape Storage.  His design makes printing the pegs easier, so get the pegs...

... at the back. And.. This makes place for a label in front :-) FYI I have to scale the tray to 106% to make it fit my bits and the box to 108% to fit the tray right off the printer. ...Probably the settings on my PLA printer that is a bit off.

A smaller version of my #Gridfinity hex bit storage tray. I specifically designed this one for my hex drill bits (the shank is hex not the bit, although that would make for a cool drill ...) and small hex bits for my day-to-day jobs. Stores 14 drill...

Here it is, the print in place hex bit storage case for 1/4" bits. No Supports I printed mine out of PETG at 0.3mm layers but I think finer layer heights would definitely help with the fit of some of the hex bits. I had a few spots that were a...

The device is a versatile eight-way hex driver bit organizer.

Parametric Hex Bit Holder This 6.35mm / 1/4" hex bit holder is designed to accommodate standard hex bits of various sizes, scaling up to large dimensions as needed. I have successfully rendered a 100x100 version of this design in Fusion 360 and...

Customized version of http://www.thingiverse.com/thing:1118772 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1118772 Instructions Using the following settings: Rows - set to 12 Add intersect holes -...

Used with these AliExpress-Items: 10 pcs Torx 1/4" Hex Bits T6 to T40 7 pcs Hexagon 1/4" Hex Bits H2 to H8 10 pcs 1/4" Hex Bits Mixed Set Related items: Drive Socket Storage Box Hex Bit Storage Box for 50 mm 1/4" Hex Bits Edit: I added two more...

Holder for my hex bit set. ...A total of 40 bits fit in the holder.

To ensure secure storage, I positioned the hex bits at a 40-degree angle relative to the front face of the holder, allowing them to stay in place regardless of whether the holder is mounted vertically or horizontally on the wall, while also keeping...

Changed from my previous version and now using four 8x3mm magnets, one placed at the bottom (layer 1) and under each hex pocket so that the magnets will hold the bits in the rack and also secure the rack on a metal surface. At layer 13 you will be...

Only changes are I added two embedded 10x2mm magnets into the base and chamfered the bit openings slightly. About 19 minutes into the print job (if you use my .3mf file) is a pause for inserting the two 10 x 2 mm magnets. If you find the magnet...

If you have any issues and suggestions please report in comments.

I thickened the outer wall of the original design, increased the number of storage, boxes can be stacked and assembled, and added another higher box type. The idea came from : https://www.thingiverse.com/thing:1975865 ...

I thickened the outer wall of the original design, increased the number of storage, boxes can be stacked and assembled, and added another higher box type. reference: https://www.thingiverse.com/thing:1975865 https://www.thingiverse.com/thing:5021804...

This is a remix from Hex box, but in this remix i made the wall more wide to reinforced the box

Keychain with built-in compartments for storing and organizing hexagonal wrench bits.

I found the Hexagonal nozzle sheath and inspired by it I refitted it to be a Hex driver bit sheath instead.additional edits:increased the space between the slots for easier access to the driver bitsmade it fit into the modular Hex set V2...

I needed to organize my loose hex screw bits and looked around for a simple solution. ...I did find solutions but they where either too small, to large or had sharp edges.Here is is my solution to the problem…There are many different sizes to choose...

I fell in love with the vertical (wall-mounted) hex bit storage by orubap, and I knew I had to give it a creative twist. So, I set out to remix the rails to make them perfect for my pegboard, which features a 12x12 mm hole grid. ... Get Orubap's...