herome gen5 3d models

... that for HeroMe Gen5, but, sadly, I still had to use supports. but either way, uses way less plastic than most of the other versions out there, and works amazing. This is only tested with the stock extruder and stepper and with the HeroMe Gen5.

This is my design to adapt the gantry of a Geeetech A10v4 to a HeroMe Gen5 e3d v6 customization.

I followed [Sebazzz's awesome guide](https://damsteen.nl/blog/2021/04/11/how-to-mount-neopixel-to-creality-cr6) to add Adafruit NeoPixel Strips to the top rail of my Ender 3 and then noticed that the HeroMe Gen5 also had an option for an LED bar on...

If you need slighty different dimensions just ask me :) Remix of: - Parametric remake of Hero Me Gen 5 Base: https://www.thingiverse.com/thing:4555571 - Parametric remake of Hero Me Gen 5 Gantry Adapter: https://www.thingiverse.com/thing:4530852 -...

Modded the gantry adapter of the herome gen5 to move stepper motor and dual gear extruder in a direct drive configuration. Print this with "at least" 50/60% infill. Support required. Please note that by moving the stepper on the back of the hotend...

The 9mm Y-offset made no sense to me, so I ditched it and merged the Gantry Adapter with the Base (less screws and nuts to fight with).

I designed this little part to add to a HeroMe Gen 5 (Base_1) to give strain relief and support to the bowden tube.

I designed this little part to add to a HeroMe Gen 5 (Base_1) to give strain relief and support to the bowden tube. Category: 3D Printer Parts

... my Ender 3 and then noticed that the Hero Me Gen5 also had an option for an LED bar on the printhead. ...I remixed both Sebazzz's strip mount with the Hero Me Gen5 LED bar to add a NeoPixel strip to the printhead.https://www.adafruit.com/product/1426

A wiring Box to sit behind the right fan on Hero Me Gen5 if it is a forward style fan. The wiring box is designed to hold a small piece of stripboard with soldered in headers for connecting hotend fans and led strips using connectors. There is...

... to the Printer Mods Modular Direct Drive v1.3 plate on the Ender 3 Pro. I edited to remove 4mm of material. This will leave a small gap between the Bondtech adapter, and the HeroMe Gen5 hotend base allowing you to bolt the adapter to the mdd plate.

I Remix HeromeGen5 dragon mount to fit Ender-5plus and orbiter extruder v1.5 and it make it so motor is point to the back of printer for better center of gravity is it matter? I don't know. ... Untested Out of filament plan to use ABS+ ...

The pen or marker just sticks to the holder with double sided tape, or there are slots for zip ties.

I remixed the HeroMe base to work for my setup with Micro Swiss Direct Drive and Linear Rails.

In a rush, I mixed the two models together so that the https://www.thingiverse.com/thing:3782865 modification would fit my HeroMe gen 5 with BMG and direct drive.

Slicing issues on original file, filled in gaps to fix. ...All credit to previous uploads, I just filled it in.

a Baseplate to fit the Gantry plate of the X5SA Pro (maybe the non-Pro too?) The original Z-Probe is mounted on the left. (Probe Offsets are X: -37 Y: 8) The Dual 5015 Fans i use are bigger and so the Y-Endstop needed to be replaced. ... I...

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655) This version has a 9mm Y offset to be compatible with HeroMe Gen 5

So I designed a few rudimentary mounting plates to the Base 4 of the HeroMe suite, and made it a bit shorter, since the wire guide doesn't need to be where it is in the original design. I went through one revision, because I forgot to put a mount...

Revised gantry clip from HeroMe gen5.

Remix - DD Plate for HeroMe Gen5 Remixed to allow for the new spacer in the Hero Me Gen 5 base plate - this moves the hot end out away from the plate by an extra 10mm or so. So after I printed mine and then wanted to convert to direct drive; found...

Couple of Notes: * There are two versions of the carriage, one is for M3x4x5mm press/threaded inserts (https://www.amazon.com/gp/product/B07WH59N6T) * HeroMe Base is compatible with Gen4 ABL mounts (https://www.thingiverse.com/thing:3182917) *...

K8200 aluminum profile to mount of the HeroMe Gen7. ...The mount should allow all the interchangeable hotends and cooling solutions for the HeroMe solution. Do as you will with it. ... This assists in reviving an old bedslinger with newer gear.

The foundation is HeroMe here: https://www.thingiverse.com/thing:3182917 If you have two 5015s, you will need to remove the small piece holding the fan on the bend side. However, if your printer is properly calibrated, the fan holds perfectly well...

This was made for the Adafruit ADXL345 which is wider then the "normal" ADXL345. ... This fits the herome gen5

SpeedDrive BMG HeroMe Gen5 adapter for Ender3 V2 This is a remix from https://www.thingiverse.com/thing:3816051

HeroMe Ender3 Sherpa Mini Mount - UNTESTED

Couple of Notes: * There are two versions of the carriage, one is for M3x4x5mm press/threaded inserts (https://www.amazon.com/gp/product/B07WH59N6T) * HeroMe Base is compatible with Gen4 ABL mounts (https://www.thingiverse.com/thing:3182917) *...

This is a remix to do 2D printing with your printer. ... I adapted the Pen Holder to fit the HeroMe Gen 5. ... It will need the ABL mount to put it

A 7mm endoscope mount to use the HeroMe BLTouch mounts, as I still use the default cr-10 V2 mount. A few variants, I found the variant (V8) which is set back 4.5mm to look round the ducts works well for me but it depends on what you have fitted on...