hero me gen 5 3d models

I am building out a Hero Me Gen 5 for the MDD so I did my best to make sure it was compatible. The output of "the Orbiter" is a little off center from the Hot End input, because the MDD 1.3's extruder mounting holes are the same distance as those...

I have designed a new mounting plate and direct drive mount for the hero me gen 5 - 6 using a 4 wheel backing plate. I am mounting this on a voxelab aquila but it should also work on the ender 3 and ender 3 v2. I have also included the Solid works...

On the Anycubic Mega Zero forum on Reddit (https://www.reddit.com/r/AnycubicMegaZero/) there were people asking for an adjusted version of the Hero Me Gen 5 (HMG5) https://www.thingiverse.com/thing:4460970 for the Mega Zero. Here it is! ...

I have been setting up to install Hero Me Gen 5 cooling system on my Ender 3 Pro, but spotted a couple inconsistencies in the documentation when choosing an extruder adapter: I had an "all-metal" Creality upgraded extruder, which is not the OEM one...

This also requires a bit more support material, I chose 0.23mm space between support interface and the part, then I ran a utility knife on top and bottom, which made removal much easier.Adapter for the official Creality Direct Drive gantry released...

--------- Adapter for the official Creality Direct Drive gantry released for Ender 3 + Dual Gear extruder to be used with the Hero Me Gen 5. I am not sure if Creality still sells it, but it's the one seen in [this video by...

[You can find it here](https://www.thingiverse.com/thing:4790273) --- Adapter for the official Creality Direct Drive gantry released for Ender 3 + Dual Gear extruder to be used with the Hero Me Gen 5. I am not sure if Creality still sells it, but...

If your slicer supports manual support enforcers, this might be the best option as it will avoid generating supports inside the slots at the front for the fan nuts. I printed the final version in Prusament PC Blend because I was interested in trying...

You can find it hereAdapter for the official Creality Direct Drive gantry released for Ender 3 + Dual Gear extruder to be used with the Hero Me Gen 5.I am not sure if Creality still sells it, but it's the one seen in this video by CHEPPrint it with...

This is a new mount for a DD Bondtech BMG for use on Creality CR-10 V2. It allows for no reduction in x-axis travel. Compatible with HeroMe Gen5 Mount. Printing: Support required, material ABS or PETG. Print with L-bracket down on the bed as...

Modded gantry adapter for the CR-10 v3 This is a remix from https://www.thingiverse.com/thing:4460970

<p>I had originally modified the remixed mount by just chopping off the cable chain mount, but I noticed it flexing during retractions. After a few tries I was able to get it to be strong enough, and not too heavy.Adding a support behind the filament...

This is a remix from the HMG5 gantry adapter "Ender_3_v2_OEM_Gantry_Adapter_9A" to better fit the X-Axis mount on the Voxelab Aquila. It still needs tweaking, unfortunately I haven't had the time to get it perfect and the wife has conscripted my...

I had originally modified the remixed mount by just chopping off the cable chain mount, but I noticed it flexing during retractions. After a few tries I was able to get it to be strong enough, and not too heavy.Adding a support behind the filament...

WORK IN PROGRESS, SLICE HOW THE SLICER PHOTO SHOWS. ...DOWNLOAD IT BY DOWNLOADING ALL, DON'T KNOW WHY IT'S NOT WORKING WHEN DOWNLOADING INDIVIDUALLY.

This Adaptor requires 4 M3-15mm Allen Socket Head Bolts.

Work in progress but I finished what I needed, so it's not likely that I'll come back to this. A SCAD version of the HeroMe Gen5 BLTouch mounting rail. Not perfect but I wanted to use brass heat-set nuts to make my build stronger. The simplicity...

All credits to Hero Me Gen 5 author, just merged and trimmed part together. During printing had a small issue with piece being too tight... Might be due to my flow rate. Lighlty trimed the hole and everything works fine again ! ... Edit 11/09 :...

Main Features: Hero Me Gen5 Base Does not go behind the hotend so it can be removed without removing the hotend Does not cover the left belt hook, so belts can be attached after everything has been installed on gantry Tunnel for the Micro Swiss hot...

I designed this to eliminate heat creep in my stock hot end with all metal heat break and also to eliminate any other unwanted noises caused by the Hero Me fan guards and my Winsinn 4010 fan.

... those captive nuts falling out. A Simple spacer to allow the Hero Me Gen5 to be used with the "cheap" generic direct drive conversion bracket commonly sold on Amazon & Ebay. ...Requires 2 x M3x40 screws also see my other parts for the Hero Me Gen5

... 2 M3x20 screws and 2 M3 nuts. === **Update 04-01-2022 (Added Hero_Me_Gen5_Base_1---Quick-Release-Rev02.STL & Hero_Me_Gen5_Base_12---Quick-Release-Rev02.STL): The slots for the Air dam were missing in the previous version. ...Corrected it in Rev02.

A remix of a remix of the camera arm from https://www.thingiverse.com/thing:4721088. ... This arm has been extended to prevent it from being hit by the left Blower duct of the Hero Me Gen5 and gives clearance for a BLTouch. ...

You'll need this this gantry support : https://www.thingiverse.com/thing:4776771 I use the Hero Me with two 5115 fan + lightweight duct standard The BL touch will be hide behind the left fan. Its kind of cool ! ...:) I ve designed and test this...

9mm to compensate for the hot end offset added by the Hero Me fan duct. I felt that the extra overhang required reinforcement so I added strengthening ribs underneath, which also required adding a little bit of height.</p> <p>I used a 44mm length of...

9mm to compensate for the hot end offset added by the Hero Me fan duct. I felt that the extra overhang required reinforcement so I added strengthening ribs underneath, which also required adding a little bit of height. I used a 44mm length of...

) I could have lowered the Body of the Hero Me another 1mm by moving the mounting holes down, but that would have required disassembly of the X gantry. Instead I found the following thing that provided the clearance needed to lower the Z further: ...

6/17/20 - 5:58pm EST: ABL Mounts are now complete, awaiting testing. They should fit perfectly. 6/17/20 - 4:45PM EST: My current version .5a is workable, accommodating the hot end and fan wings. However, it requires a slight modification to the ABL...

We also have other pre-parametrized files: - **gantry_adapter_1b.stl** attempts to replicate the original **CR-Ender_E3D_Gantry_Adapter_1B.stl** file from Hero Me Gen 5. It is designed for use with E3D V6, Volcano, TH3D Tough, Mosquito, or V6 clone...

I could not fix all the symmetry issues due to the costraint of being compatible with the original Hero Me Gen 5. Notably the V6 Screws have a different distance from the center (11.3mm to the left and 10.75mm to the right). Additionally, there are...