henry cavill modeling

Buildings 1) Human Living Space -This is the repurposed spaceship used to fly to Mars -It is already radiation-proof out of necessity from the trip to Mars -Already equipped with heaters from space travel -Much of fuselage is repurposed into a...

It does not matter which direction is taken.Continue running the line down and up between the pieces through different holes until it is fully connected.The line must turn a corner on the bottom piece, so ensure that it is placed completely in the...

This new model boasts significant durability enhancements, enabling it to withstand heavy grounding without sustaining terminal damage - a critical feature for FPV enthusiasts, especially during the learning phase. I won't claim that it matches the...

Printer Settings: * Printer Brand: MakerGear * Printer Model: M2 * Rafts: Doesn't Matter * Supports: Yes * Resolution: 0.4 mm nozzle * Infill: 30 - 60% * Notes: This is a very big object, taking a lot of plastic (~1/3 - 1/4 of a 1kg roll) and many...

the vanilla singleplate model), though the pulleys included here are a bit different from those. Re-cut bolt/nut holes in the idler pulley holder and thumb wheel to accept M5 hex bolts (because those are all I have with hex heads :-P ) Added an M5...

The handle houses the controller with its user interface and no base unit is required.All that is missing to be the perfect soldering solution for workbench and mobile needs is a stand and a housing.Introducing TStationThe TStation is a case for the...

Perfect for storing jewelry, electronic parts, cables, Lego models, tools, and other small items, the Pyramid Stacker offers a practical solution for keeping your belongings organized and within reach. By stacking the layers, you can store smaller...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

One uses a buck converter that is very difficult to find at the moment, so this model is not uploaded. This is the one I use. The other one has a larger area inside so you can fit other converters, should you want to. You can ignore the converter and...

This model fits seat shafts with a 16-groove, skip-tooth-top, 12mm nominal shaft: (note skipped groove, blue arrow) Probably best to print these with the spud pointed up for minimizing how much trouble the overhangs inside the hole will...

I usually split such models on 2 or 3 parts that are easier for printing. Then these parts can be glued as a one piece (with acetone for ABS, or dichloroethane for PLA). So other version of parts I am uploading is prepared in this way. My black...

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...

I design a Electronic Bay Cover with LED Light Just a little favour>>>Less then 10% of downloaded Models get a like.→ If you like the design, it will be nice if you click on the like button and maybe share your print.   Its a heavy redesign of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

The reason for the former changes is the way I modeled the original was a PITA to modify so some things had to get completely redone (and I left out the less important details to save time). The reason the STL's are so large is simple; I upped the...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

...March 23rd - Created a smaller prototype mockup for the bottom, mid and top tray using measurements from the full sized model. Experiencing corner lift on the middle tray, even with brims and the lid/bottom of the middle tray is about 1mm too short.

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

 I am hacking stuff together in Tinkercad, so parts of the original Voron panel retention clips and hinges were used in creating these.I plan to make matching latches in the future, but for now am using these panel...

... you'd like to copy it into your workspace and mess with it. [Buy me a coffee :)](https://www.buymeacoffee.com/jcolega) - [Printables](https://www.printables.com/model/152611-lego-vehicle-wall-hangers) - [Thangs](https://social.thangs.com/m/65559)

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

If you do this, use the "Pusher Extd" model. To modify the solenoid: 1. Remove plunger. Remove about 3mm of the black base and sand flush with the metal slug. Sand the black base to make it slightly thinner if you want to add an additional spring...

Using the paint supports tool in PrusaSlicer, put supports around the square cutout that you can see by looking through the bottom of the model. Look at the image below for reference.</p><figure class="image image-style-align-center image_resized"...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

Any longer and you'll have to either modify the model or hold it steady by hand while screwing in the first few mms until the guide grooves engage. Any shorter and you'll lose variable length and have to use a tighter initial state for the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

... can get rather hot. PLA may work; I'm not sure. Use a minimum of: 3 perimeters 20% infill 4 top and bottom layers The model for the base plate isn't oriented correctly-- print it flat with the side labeled "TOP" upwards. Category: 3D Printer Parts

&nbsp;For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base. &nbsp;The adhesive mount’s socket is smaller...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...