height comparison tool 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 shape =...

For those please use paint-on support like this:My tips to make watertight prints:Increase the flow rate (extrusion multiplier) to 105% (1,05)Ironing can be used (print settings → infill)Infill overlap 15%Increase the nozzle temperature by 10°CLower...

I printed most of it with a layer height of 0.2mm and 20% infill. Some Parts need Support. Have fun printing and driving Dies ist ein fast komplett gedrucktes 1967 F1 RC Auto im Maßstab 1:8, dass ich an einem 1967 Eagle angelehnt...

If, like me, you use a printer with a bed that moves in the Y direction (like an Ender-3), you will notice that once the print reached a certain height it will start wiggling and vibrating a lot. You will end up with a part with a clean bottom but a...

Screws: 2 M3 x 30 SHCS for KNOBS and 2 M3 x 16 SHCS for corner pulleys.TENSIONERS: Have different post height for correct belt positionInstall thinnest PULLEYS, screws: 2 M3 x 16 SHCS. Install TENSIONERS on the FRAME, TENSIONER with shorter post goes...

For models like this use a height range modifier.1.2.3. The high speed, pattern and heat make a bad print.The tiny hole in the middle and the concentric pattern limits extrusion's inaccuracies.AssemblyCounter shaft counter 2ndcounter...

This convenience comes with disadvantages, however: this 16-cup design uses far more material, the size of the part makes it susceptible to warping away from the bed if printing with PLA, it requires a longer feed path (or mounted on a raised...

I have used silver, but you can use black as well.Print InstructionsI have printed everything in PLA at 0.15mm or 0.2mm layer height.You will always need the following parts:PartCopiesColorSettingslower_emitter1silverironing, supports on...

The worm gear drive provides sufficient torque to generated the fore and aft motion of the hummingbird, and for the face gear 4:1 gear ratio that provides four wing flaps per fore and aft motion.I 3D printed this model in Tough PLA and while Tough...

The spacer is needed to get the small pulley to teh same height as the big pulley. You may ned to tweak this a bit taller by stretching it in your slicer. Its a very quick print. Lastly, youll need a way to connect your tripod and hold the RA...

The end mill caught me by surprise and drew blood.Print instructionsI made the body in PETG, .2mm layer height, 3 perimeters, with 40% infill. Clamp printed at same settings but 100% infill. ...You don't need any supports if you orient things correctly...

A lot of thought went into fit here :) - Install pictures are below General print settings - .20 quality (each part group is detailed so if something is different it is listed there) - Infill will vary from 20-80% and will be listed - 35mm Print...

It has also been designed to allow individual customisation with Lego blocks and/or card cut-outs that insert into custom 3D printed Lego-compatible blocks (the files for the LEGO-compatible blocks for card cut-outs are available here). All the...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes wall_thickness = 1.6 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_clip = 95 pattern_copies = 30 pattern_rotation = 180 inner_diameter = 60 height = 10 pattern =...

Expertly crafted drones tailored for capturing stunning videos assistant Specialized, high-quality drones designed for professional filming purposes. assistant High-performance drones engineered specifically for top-notch video recording. assenior...

4) Only needed if printing the "stream" upright: then use a smaller nozzle when printing, or at least with somewhat small layer heights (about 0.24mm), so the lines don't show too much on the near-horizontal areas. Some lines may actually add to the...

Using the following options: qr_size = 37 qr_bottom = 1 obj = 1 code_flip = 0 tag_height = 80 qr_y = 0 qr_x = 0 tag_width = 80 qr_tolerance = 0.001 case_thickness = 1.8 add_sub = 2 per_h = 10 per_w = 3 round_corner = 2 tag_thickness = 3 corner_num =...

Model height: 175 cms Advanced rig with IK/FK controllers (.blend) is available automatically after installing the AutoRig Pro plugin Character is made from the scratch, without the use of Daz models, scanning method and others Low poly, game-ready,...

When engaged in a full frontal attack, they are quite literally, unstoppable.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

- Download Retropie for your pi https://retropie.org.uk/download/ - Win32 Disk Imager download https://sourceforge.net/projects/win32diskimager/files/latest/download Burn the files to your SD card and edit the config.txt adding the following lines...

Attention!Since i now work with 'Fusion 360' every part will be redesigned from scratch.Check regularly for updates, they'll be listed here.Ender 3 Control and power AIO modular enclosure: Parts you need to order for this Card reader extender for...

 When the fan is inserted it bends the inner walls of the upper brackets to create a good seal and make the dimensions work so the filters create a perfect square.Recommended Printing ParametersMaterial: PETGNozzle Size: 0.6mmLayer Height:...

Change if you are using something else (trying to use up what I bought a few months ago.)Use variable height to smooth out the curves on the light.Designed on...

You're using this model at your own risk etc.Print settings / orientationI recommend slicing with PrusaSlicer 2.5.0 (currently in alpha).0.20mm layer height, 15% infill.PLA has worked great for me, try finding a color that has minimal...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

The fixture`s overall height, including the adjustable surface mount bracket, is under 4.5", making the EPL-LP-2X48-LED one the lowest profile explosion proof light fixtures on the market. When compared to our EPL-48-4L-T6HO fixture, the...

Another workaround would be reducing the height of the display side's segments, but it's already pretty small… And yet another would be increasing the length of the arms, and with that, the distance of the display thing.No detailed assembly...

The parameters with which the pieces were printed in my case were: low quality profile with layer height of 0.28mm, 10% cubic infill and support for the pieces and adhesion Raft was used (see picture above for more details).The material used for...