heewing t1 vtol 3d models

V 2 of the Hatch, now with a fixed SMA Connector and some additional cooling for the VTX wich also adds additional strenth if you print this with very thin walls.

Not 100% fit, but ok. ... recommane LW-PLA

Slicer used CURA Wall line count 5 infill 100% Suporte YES! ... Material PLA or PETG Works Much better than Original one Enjoy Guys Im using aloft hobbies foam wheels

FC mount for Omnibus F4 Pro. ...Also good for every 30.5x30.5 FC

It was only a few landings in when the hub in the OEM wheel broke. This is one I just designed to replace the OEM hub directly in the OEM foam wheel. It's also built to attach to this 3D printed landing gear:...

Slicer used CURA Wall line count 5 infill 100% Suporte YES! ...Material PLA or PETG Works Much better than Original one Enjoy Guys Im using this foam wheels https://alofthobbies.com/gws-51mm-x-21mm-axle-foam-wheels.html

Cut a hole for Matek M8Q-5883 GPS Module w/ Compass to pop through. ...Used CA around edges for flush fit.

Heewing Ranger T1 Rear cover with Rush Tank Solo vtx mount. Use an antenna similar to the one shown in the pict. Replace the original Rush screws with M2x10 and secure the VTX with the nuts on the back side. ... Do not glue the antenna, insert...

May fit other cameras too.This was designed for the T1 but it fits the T2 perfectly too.Just a simple design for a front vent cover pan servo mount. The pan servo screws into the mount at an angle for better forward viewing.Cut out space for the...

<p>This is a tray that holds the BN-880 GPS and allows the wiring to drop down through either side.</p> <p>I had seen a couple of other designs that required gluing into the fuselage, but my FC is mounted under the spot where this fits, so I needed...

I remixed the Cam Mount to beef it up a bit since I am using it for an analoge cam (and the Hybrid) and need space for the connector. ...(work in progress)

Needed an Exhaust venting rear hatch as the front of the model allows air in but not out. this resulted in DJI air unit inside getting hot. This solves that. Thanks to the original designer of the hatch saved me drawing it. ...Added a hole and some bars...

[edit] I have added a V2 which is lighter, but more importantly, allows a lot more breathability on the bottom, where the Air Unit gets hottest. I will be added a vent just below this spot (in the belly camera mount position) to bring fresh air in...

This is a tray that holds the BN-880 GPS and allows the wiring to drop down through either side. I had seen a couple of other designs that required gluing into the fuselage, but my FC is mounted under the spot where this fits, so I needed it to be...

I installed the VTX in the nose behind the camera; I was looking for a way to attach the antenna without making any holes. The piece is tied with hot glue and sticks well. ... I added a new version, v13, to place the antenna in the middle of the...

[edit] I have added a V2 which is lighter, but more importantly, allows a lot more breathability on the bottom, where the Air Unit gets hottest. I will be added a vent just below this spot (in the belly camera mount position) to bring fresh air in...

This is a replacement cover for the landing gear mount. It does not include holes for the landing gear, it is meant to make the bottom smooth. ... Print vertically

This mount will allow you to mount a DJI Airunit above a flight controller in the Ranger (you will need to use a WSE sized controller) i am using the 765-wse. it hinges on the spar and allows for you to close the canopy just fine. Note that there...

Mount for DJI o3 Camera. Needs four M2 Brass Inserts. ... Base Plate gets glued into the plane.

This is a rear hatch to move the PNP Betian GPS from the front to the back.I don't really think the GPS needs venting, but it looks cool. ...:) Less plastic might allow for more GPS signal, maybe...?I printed with 25% gyroid infill, 3 bottom layers, 4...

i tried different designs but all didn't had enough airflow so i designed this and it works pretty good.

This mount holds a nano-sized camera and 5g-sized servo. For the hinge you need 2mm cf rod. mirror the front part and glue both together. I printed the front part out of LW-Pla and other parts from PETG or PLA+. ... After cutting a hole in the...

This thing is for mounting a HDzero Freestyle VTX to the front of the fuselage. The bottom part has to be glued in and the top part screwed onto that. ... you need 4 M3 screws with nuts.

A quick remix to add 1mm shoulder around the VTX mounting holes to avoid the use of washers. Changed the two plate mounting holes to slots and extended the antenna mount by 13mm to get the antenna up higher. ... Some patient cutting of the foam...

TBS Immortal T antena holder placed on the tail boom. Antena is fixed with two zip ties. There are two additional paths for zip ties to ensure stronger fixation of the holder to the tail boom if needed. ...

Tail camera mount for 3rd person view fpv experience! Designed for nano sized fpv camera. Mount it glue or thin double sided tape, and optionally secure it with m2 screw with nut. ...Resize the hole if needed using sharp blade