headphone cable protector 3d models

A special version for the right side is also included specifically for use with the air filter.) Bonnet: - Bonnet bump (bump version has the engine clearance bump and is more accurate to real life) - Bonnet smooth (doesn’t have the bonnet bump)...

Though it's not really needed to put the controller there if you what to use another type, or just want to place it with the rest of your electronics. Also, as the motor controller supports two motors, you could place it in one of the tracks, and...

170x105mm ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

Note I would advise against using the simple grill version on the left side, unless you plan to use a custom fan solution that pulls air across the controller board, but for symmetry, I just had to include it (OCD!) About the left side The left-side...

Board Arduino Nano processor ATmega328p if you are encountering problems try unplugging from the cable then plug back in and change the processor to ATmega328p (old boot loader),with another Arduino UNO I had to set this to old boot loader to make...

MiSTer USB-C Power Delivery dongle Clean up some cable mess and replace your weird "lamp" style switch with this USB-C power delivery dongle. This simple and inexpensive design lets you use modern USB Power Delivery compliant phone/laptop chargers...

There are several of them, my favorite is probably https://www.thingiverse.com/thing:3615910, but check out the rest of his thingiverse for some alternative designs. But, if you, like me, want to have a little arm of these guys that you can pull out...

120x92mm ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

I've also included a mouse hole for the back of the enclosure, allowing power cables to pass through. This hole can also be cut with a jig saw. I really liked schlem's swivel pass-through for his enclosure design (see...

| Part Ref | Quantaty | Shop | |:-------- |:-------------:|:---------------:| | TTGO T-Display | 1 | [Aliexpress](https://www.aliexpress.com/item/33048962331.html),...

105x70mm ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

90x52mm ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Tinkercad link: https://www.tinkercad.com/things/7aYnpLajauz ________________________ Some of my other designs:...

Since the Raspberry Pi on the RatRig is located remotely, it won't be mounted on the back of the screen as is typical.Hardware Required:1 x Raspberry Pi 7" Touch Screen (https://www.raspberrypi.com/products/raspberry-pi-touch-display/)1 x DSI Ribbon...

piping/cabling for the units. Construction is designed to be performed primarily by robots sent on an unmanned construction mission. These robots will, upon landing, produce initial pieces of the agriculture / construction dome within the...

75x46mm ________________________ If you like my work please consider supporting me on Patreon. Become a Patron! ________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

https://www.banggood.com/custlink/mKm3093MQT Power jack for TS100 5.5x2.5mm connector (To build flexible power cable use silicone wires, they are heat resistant and flexible): https://es.aliexpress.com/item/32778311364.html Simple TS100 stand:...

LED or camera mount points, along with their respective cable guides, can be added easily given that the .scad file is provided. This item is fully parametrized due to differences in printers and extruders, which I experienced while searching for a...

some wire (I used some from a dead keyboard cable). 1x LED (you could use the one from the button, But I went with cakelights as they also come with batteries,...

(Open source firmware for ESP devices: https://tasmota.github.io/docs/) In my case, the power supply is 24V, as the supply cable is quite long. A stable voltage of 5V can be set at the D1 Mini by means of the LM2596 DC-DC buck converter voltage...

I also used a standard fan resistor cable to step down the 5v to 3.3v in order to reduce fan speed and noise.The result is a really quiet and really cooler computer. It hardly goes over 45°C.&nbsp;<br>The negative side is that I originally planned to...

1-, 2- and 3-slot "mesh" blanks (36mm, 72mm & 108mm) Pi 4 and Jetson accessory mounts include options to allow for the following (or similar) front-facing MicroSD extension (fits pretty snugly, but a little hot glue will be a little more secure):...

All of them are compatible, including the actively cooled ones.Prusa Bear-style aestheticsShort path between Raspberry Pi and the electronics case allows very short USB cablesSTEP file available for easy remixing&nbsp;BOMQtyDescriptionSourcing1Armor...

## Printed details - 1 x Base Front Right - 2 x Base Rear and 1 x Base Front Left - 1 x Door Handle - 1 x Door Stop - 2 x Hinge Bracket - 1 x Hinge Front Left Bottom and Rear Right Top - 1 x Hinge Front Left Top and Rear Right Bottom - 1 x Leg...

That notch is for the cable and plug that goes into the fan, since that plug sticks out slightly. To run the wire to the fan, drill a hole through the top of the leg, the printed corner piece, and the underside of the table. The inside of the table...

I inserted 2 pieces of copper into the slots next to the sprocket to use them as power distribution - wires and jst plugs to connect everything Assembly ------------- - print all parts - glue the bottom ring to the bottom tray - screw bottom ring to...

You need 1 m LED strip with a width of 8 mm, a few wires, cable clamps, GU10 sockets and a small power supply for the LED strip and a couple of M3x20 screws and matching nuts. If you use a strip with 60 LEDs per meter, I recommend using a power...

________________________ Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool https://www.thingiverse.com/thing:4654396 - Rivet Placement Tool https://www.thingiverse.com/thing:4165457 - Smoke Stack Addon for...

cable ties), 26 cm each, depending on the vacuum cleaner adapter * Vacuum cleaner First: If your printer isn't calibrated yet, print a test cube and set the stepping for the Z-axis accordingly: Z-Soll/Z-Ist*Stepping Do the same for X and Y. The...

You can then buy a cheap power supply and rca cable or invest in a battery cartridge grip and basically turn your machine into a tattoo pen. Cartridge grip (~50$): https://s.click.aliexpress.com/e/_DEuIZp1Rca connectors (~1$):...