hdzero nano 90 3d models
63856 3d models found related to hdzero nano 90.
prusaprinters
Nice little camera holder for the HDZero Freestyle VTX to hold camera and included antenna.Prints out of PLA+/Tough PLA, PETG, ABS or TPU. I would not print out of standard PLA just because it may be too brittle for the screws to thread in. ...Supports...
thingiverse
This is a folding mount for using four TrueRC x2-air antennas on an HDZero VRX4. The side antennas can be folding sideways for more omni coverage, or all forward for maximum range. The hinges are sized to use 1.75 mm filament as the pin. ... I...
thingiverse
Nano VTX Options That Will Fit - TBS Unify Pro 32 Nano: A very reliable 400mW TBS quality, but a bit expensive. - Eachine Nano: Really does 400mW and never had a single one fail. However, there seems to be a certain percentage that arrives with...
thingiverse
Nano Quad Wings & Rotorgards Fits Revell uk and I think Hubsan nano quad if this is the same ESTES circuit boards. But has flex so could fit most copters. Shape to fit with worm water. Loreal shampoo, science... Pros... 1. Increase glide and...
thingiverse
There's a case for combining an Arduino Nano with a LM2596 DC/DC Converter. I need it for one of my projects and it could be useful for others too. 1 hole is needed for the arduino nano usb port. ... Versions with holes include: 2 holes for cables 1...
thingiverse
Had to do this in order to fix the issue with HDZERO messing with the gps. ...To fix completely the problem the camera mipi and the gps cables were shielded and grounded, and the SMA pigtail was grounded, and finaly i found that higher gains antennas...
thingiverse
New HDZero goggle sliders for X-AIR MKII True-RC patches. - Patches fit perfectly on sliders (same lengh) - gives more cable length, to plug into upper SMA connectors. ... - Also can be used to connect to lateral SMA connectors - gain space to fit in...
thingiverse
I remixed a DJI mount to fit the HDZero Freestyle VTX and Runcam Mico V2 cam. Print in a material that can withstand the heat the 1w VTX could generate. You might need to rework the M3 threats or use M3 inserts in the holes. I also remixed a SMA...
thingiverse
Mounting the HDZero on top of the controller using an interface plate takes up space and reduces necessary cooling airflow; To resolve these issues heatsinks from a previous projects were cut up into a 20mm x 20mm block, mounted slightly back on the...
myminifactory
It allows for mounting off either just and HDZero/Sharkybyte VRX or a HDZero VRX and a Skyzone Steadyview X VRX. The VRXs are mounted upside down to optimize placement and to minimize torque out front of the goggles. I hope to be able to make a...
thingiverse
... (I used the white paper from double-sided tape) I know this may not fit everyone's hand. For instructions and inquiries for changing geometry for a better fit, leave a comment at: https://www.electric-skateboard.builders/t/nano-remote-mod/70835
thingiverse
... hole facing down as it will enable the other end to be bridged. Refer to attached PrusaSlicer image for orientation. Made for: TrueRC X-Air MK II https://www.truerc.ca/shop/5-8ghz-2/receiver-long-range/x-air-5-8-mk-ii-pair-for-hdzero-vrx4
thingiverse
You can use it to install a HDZero Freestyle 1 Watt VTX in your drone. Version 8: * Fixed a few problems with spacing. * Cables can now be placed either above or under the part. * Added extra reinforcing for the standoffs * Standoffs shortened...
thingiverse
The Sliding HDZero Goggle Caddx VRX Removable Mount is a design that allows the VRX to be easily removed by sliding it out. At the same time, the clips stay with the goggle for secure attachment with room for the antennas and enough clearance. The...