hdo mod 3d models

VIDEOS A simple quick and dirty demonstration by me of how the knob works:https://www.youtube.com/watch?v=yPHjmhsJESk And a more professional video by Chuck Hellebuyck on how to install the knob (and some other useful CR-10 (mini) mods) on Filament...

Other mods have you print a spacer to hold the v6, but I think that's a pretty bad solution, sacrificing lots of rigidity and stability. This system eliminates that, but still leaves the spacing issue. I fixed this by simply lifting the heated bed up...

This needed a few mods to the clock body to make it fit.The total width of my remixed clock is about 60cm.Clock mechanism :  “LEZ” “silent” sweep type. (from eBay). Thread length: 15mm. Total shaft length: 21mm. Shaft diameter: 7.5mm.  The shaft is...

My mods are: 1) Took the source .stl files and split the body into top and bottom. 2) Hacked in an access door into the bottom with plenty of room for a small breadboard, 3) made the ring thingy a bit taller so as better to control the sharp edges of...

If you're reading this, be aware that this mod requires a light hardware modification, potential soldering, and a firmware tweak. Must be running Marlin Firmware! I got mine from Aliexpress, but you can get them anywhere really. Optical Pros &...

------------------------------------------------------------------------------------------------------------------------ Old Description...

... It's also possible to build the mod with 9mm wide belts, but if you attempt so, please contact me to alter the idler holders for 12mm idlers. ... Even though the build itself is rather painless, I advise only seasoned 3D printers to attempt it.

:-) This mod is verified to be compatible with: - Ender 3 S1 - Ender 3 S1 Pro - Ender 3 S1 Plus As of version 4.0, this duct is compatible with: - Spider Hot End Mod (3.5mm lower, use the provided STL, not the stock one) This mod is NOT (yet)...

This Z axis mod was designed to eliminate the need to completely remove the Top Z-Axis bolts, which could lead to getting the z-axis top frame out of square and causing issues for new installers. By using the top 2 screw brace it allows a new...

This is a bigger mod including a lot of steps, so nothing for the fainthearted among you ;) You have two possibilities here: 1.) USB cable Version with a visible cable running from the base to the tracker, its less work but there is always a slight...

Published project parts so far: + Fluval Flex Cooling Fan Adapter 40mm https://www.thingiverse.com/thing:3640543 + Fluval Flex Cooling Fan Adapter 80mm https://www.thingiverse.com/thing:3671625 + Fluval Flex Filter Mod...

I personally used 0.1 or 0.2mm in PrusaSlicer wihile printing on my heavily modded Ender 3 with direct feed. The ratcheting part of the strap arms are curved behiend the back of your head inside the mechanism. To achieve the curve like the...

Join the community discussion, get assistance, or even show off your mods! DISCORD: https://discord.gg/aE49DW2xXe Visit my Github for the full BOM for this assembly or to get the STEP files for modification. GITHUB:...

This mod concept originated from http://www.thingiverse.com/thing:661936. The recommended modified idler with enhanced tension against the MK8 gear can be found at http://www.thingiverse.com/thing:487891, producing smoother filament flow. With a...

-Towers Tray = Same mods and settings as the Figures Tray. I figured I would take out the extra step up around the towers too again just to save on unnecessary plastic even though the original feature does look cool. Give and take. -Bottom Row...

I appreciate if you post a remix, if you do any mods. The photos should be as follows: 1. Completed Fume Extraction System. 2. Main body of fume extractor, the base that the printer sits on, shown upside-down. It should be printed as provided...

I remixed this from 3 different models (thingiverse's post a remix option is not working for me, so instead of the links being on the bottom left of the page, you can find them right below): - I liked the mushroom cap design of the clip for the...

Or if you use an external camera without a Raspberry Pi and you want a static image of your bed while printing, then this Ender 3 mod is for you! This model is directly attached to your printer bed, so in the video it will lock static even if it's...

Update 1: Get the Tractor Trailer at: http://www.thingiverse.com/thing:1967778 Get the Motor Mod for Standard 540 Size Motors at: http://www.thingiverse.com/thing:1967812 Update 2: Get the Tractor Fertilizer at:...

With Repetier firmware, an E3D-V6 hot end, custom extruder, cooling fan and shroud, new glass bed, rearview mirror, some tweaks to bushings to get rid of slop in Z, access hole to SD card for standalone printing, top access door and now cable carrier...

For leveling you can put a bench level across the flat part once assembled and up against the wall and then mark your holes.As always I have included the STEP file If you want to mod this (any real CAD package can import this - obviously it is metric...

... room. That's why you can remove the glass, the big 90-teeth gear with belt, fold the glass holders, and store everything anywhere. Printer Settings: - Printer: Heavily modded Anet A6 - Rafts: No - Supports: Yes - Resolution: 0.15 - Infill: 30

The nozzle I remixed from here https://www.thingiverse.com/thing:13898 required some serious tweaking to get it right, even after I modded the rear thread to be smooth. The fins were almost separate initially, so I had to make some adjustments. The...

fan adapter and modded Prusa MK3 Layer Cooling," found at https://www.thingiverse.com/thing:3512817. The carriage and BLTouch mount parts are designed to work with the cooling system, which can be downloaded from this page or used with a basic E3D...

One System Per Mod, If This Is Your First Night at Plumbing Club, You've Got to Plumb. This Design is Intended for Low Pressure Return Pipes for Grey Water at Approximately Room Temperature. Do Not Use on Gas (Propane, LPG, Butane, Domestic Gas...

I used AWG 20 silicon wire for the BMS connections.Zvones52o did the heavy lifting with his battery eliminator back piece for the GD-77  https://www.thingiverse.com/thing:2742838 , I just made some mods in Tinkercad to accommodate addition of two...

You can also use a rubber band around both clips under the chassis to help keep them on if they don't hold enough.Props/credit to!62Marder, I used his battery clips and modded them adding the side mount from the pull back racer...

Attached you can find the assembly instructions and Marlin 2.0.9.2 firmware for this mod. This firmware is for SMT32F1 chip. If you have the last version of Kingroon, you need compiled the firmware for SMT32F4 chip...

All parts are connected together using bayonett-type connectors so you can take them apart and clean everything.I included the STEP file for the connectors, so you can adapt to your own hoses.You could also use a plastic bucket instead of the...

When combined with the LED mod, your prints will be perfectly lit, as shown in the provided image.Support-Free Printing: Designed to be printed without supports for a clean finish.Simple Assembly: The battery box needs to be assembled using...