hdmi csi 3d models
4350 3d models found related to hdmi csi.prusaprinters
This is a case for an HDMI-CSI module sold on Amazon for use with the RaspberryPi4. ...Requires 4x M2.5 screws to hold in place.</p><p>All parts printed with minimal supports on plate at 0.20mm resolution and 15% infill.</p>
thingiverse
I needed it to fit both my HDMI CSI adapter and a 30mm canakit fan I had lying around, so I extended the top of the case and widened the vent that was provided in that design. ... As stated in the original, it's designed to work with any bottom piece...
thingiverse
This is a box to fit a [HDMI to CSI Adaptor](https://www.arducam.com/product/arducam-csi-hdmi-cable-extension-module-15pin-60mm-fpc-cable-raspberry-pi-camera-specific-pack-2-1-set/) Couples nicely with the [Raspberry Pi Camera...
grabcad
https://www.waveshare.com/hdmi-to-csi-adapter.htmThanks to HAMZA CHAFRA for the HDMI ConnectorHDMI connectorThanks to Xgentec Jason for the 15Pin Ribbon Connector15 Pin Ribbon Cable Connector
grabcad
https://www.waveshare.com/hdmi-to-csi-adapter.htmThanks to HAMZA CHAFRA for the HDMI ConnectorHDMI connectorThanks to Xgentec Jason for the 15Pin Ribbon Connector15 Pin Ribbon Cable Connector
prusaprinters
An enclosure designed for HDMI to CSI-2 Module(based on TC358743XBG) that designed for Raspberry Pi. You can easily find similar module on the eBay (such as this one).To assemble this case, you will need the following non-printable parts:M2.5x10...
thingiverse
Housing for the HDMI (out) to CSI-2 converter for Raspberry Pi. This is compatible with my Raspberry Pi 4 case. ...I use this converter casing in conjunction with my Raspberry Pi 4 case.
thingiverse
Raspberry Pi 4 case with HDMI to CSI-2 module. Designed to use with screws. I used screws typically found in gameboys. ... Perfect for Pi KVM project.
thingiverse
I really like the design from evancli for RPi4 with HDMI CSI Card. I make the slot bigger to fit CSI to HDMI bridge card for Pi-KVM. I also remove the top OLED mount because it will not fit with the larger C779 module. ... Update 4/6/2021: Add base...
prusaprinters
I really like the design from evancli for RPi4 with HDMI CSI Card. I make the slot bigger to fit CSI to HDMI bridge card for Pi-KVM. I also remove the top OLED mount because it will not fit with the larger C779 module. ...Update 4/6/2021: Add base with...
prusaprinters
I really like the design from evancli for RPi4 with HDMI CSI Card. I make the slot bigger to fit CSI to HDMI bridge card for Pi-KVM. I also remove the top OLED mount because it will not fit with the larger C779 module. Update 4/6/2021: Add base with...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
Remixed Nashuar's design to accommodate Geekworm's HDMI to CSI-2 C779 module which is 5mm wider (50mm x 35mm) and removed the etched lettering for easier 3D printing. ...
thingiverse
Per a request that I got, a remix of my remix to mount a HDMI TO CSI-2 adapter and RPi4 in a single case. ...Having trouble with Thingiverse so I will update the model with addition files when the platform decides to function properly :P The top can...
prusaprinters
This is a remix of "RPI Cam + Arducam CSI-HDMI" by nperto on Thingiverse that rotates the attachment 90° and attaches to the opposite side. Designed to work with the arm/pivot from...
thingiverse
The included lid doesn't close properly. Redesigned to fit exactly. ... Using it with this for my pikvm: https://www.thingiverse.com/thing:4713619
thingiverse
Designed for Tech Enthusiasts Everywhere, This is a Game-Changer for the HDMI to CSI Bridge Revolution. This cutting-edge board empowers users to seamlessly interface their GoPro or any camera with an HDMI output directly with octoprint and...
prusaprinters
This is a case for the HDMI to CSI Bridge. ...This board allows using a GoPro or any camera with an HDMI output to interface directly with octoprint and octolapse. More info at snrtechbytes.com Board: https://www.aliexpress.com/i/33009938105.html...
thingiverse
This is a case for the Arducam CSI-to-HDMI upgrade module, mounted with the RPI Cam V2. - 2 types of casings and shades: T1 and T2. T1 has a fixed shade, at the position where the case mount points to the right. If you want another fixed...
grabcad
This is a case for the Arducam CSI-to-HDMI upgrade module, mounted with the RPI Cam V2.2 types of casings and shades: T1 and T2.T1 has a fixed shade, at the position where the case mount points to the right. If you want another fixed direction,...
prusaprinters
Arducam CSI-to-HDMI Adapter mount. I used VHB tape to stick in the electronics bay of my Voron V0Used hardware:4x M2x5mm self tapping screws
thingiverse
... the pesky ribbon cable that was constantly obstructing my view. ...I've been thoroughly satisfied with this camera mount, so I decided to create a makeshift modification to accommodate both the CSI to HDMI adapter and the Pi Camera or ArduCam.
thingiverse
You need a few 2mm self tapping screws (pan head) to put the three parts together and to fix the CSI-HDMI adapter to the case (to ensure it stays in place when connecting the HDMI cable. I've used eight 8x2mm for the case assembly and four 5x2mm for...
thingiverse
Purpose: - Still trying to work out where I want to mount a Pi Camera so purchased the ArduCAM CSI to HDMI boards, these little cases for both sender and receiver just snap together with no fittings required. ...Shouldn't be hard to graft on your own...
cults3d
Purpose: - Still trying to work out where I want to mount a Pi Camera so purchased the ArduCAM CSI to HDMI boards, these little cases for both sender and receiver just snap together with no fittings required. ...Shouldn't be hard to graft on your own...
myminifactory
A complete list of materials are - 1x Raspberry Pi 4- 1x Arducam CSI to HDMI Cable Extension Module- 1x 0.91in 128x32 OLED- 2x M2.5 x 6mm Flat Head - 2x M2.5 x 8mm Flat Head - 2x M2.5 x 12mm Flat Head A M2.5 tap is needed to tap some of the holes or...
thingiverse
Rasberry pi camera mount for CSI to HDMI converter for UC-261 PI Camera Board. Requires 4 heat sets. 5mm tall, 3mm bolts. ...Converter board needs QTY:2 2mm bolts ...
thingiverse
It supports a Raspberry Pi 4, one end of the [Arducam CSI to HDMI Cable Extension Module](https://www.arducam.com/product/arducam-csi-hdmi-cable-extension-module-15pin-60mm-fpc-cable-raspberry-pi-camera-specific-pack-2-1-set/). and a [0.91in 128x32...
prusaprinters
It supports a Raspberry Pi 4, one end of the Arducam CSI to HDMI Cable Extension Module. and a <a href="https://www.amazon.com/gp/product/B0761LV1SD?tag=thingiverse09-20">0.91in 128x32 OLED display</a>. A complete list of materials are1x Raspberry Pi...