hd lifecam 3000 3d models

LifeCam HD-3000 Stand Riser - 90% Scale This adjustable stand riser provides a stable and secure base for your Logitech LifeCam HD-3000 webcam, allowing you to position it at the perfect angle for capturing high-quality video. ...The sleek design fits...

Mounting bracket for Microsoft LifeCam HD 3000. Ideal for mounting camera under the top IKEA lack desk. For assembly one M2 x 20 Screw and one M2 Nut is needed. Print instructionsBottom part can be printed without support. Top Part was printed with...

This clip secures the LifeCam HD-3000 camera firmly in place. ...To remove the protective bracket, you'll need to either disassemble the camera by carefully opening it up and fiddling with its tiny screws or use a Dremel abrasive cut-off wheel like I...

Additional Requirements: Microsoft Lifecam HD-3000 OctoPrint with a free USB port The original housing of the Lifecam HD-3000 will be completely removed and disposed of, but the four screws will be reused. Opening the Original Case (see picture): ...

This clip provides secure mounting for the LifeCam HD-3000 camera. ...You'll need to remove the floppy rubber-covered bracket by either opening up the camera and fiddling with impossibly tiny screws, or do like I did and cut the thing off with a Dremel...

Some basic files to hard mount a Lifecam HD-3000 on your robot. Can be used for the camera alone or add a high power LED on a heatsink. Details still TBD but see the notes section. Also on Github: https://github.com/Techbrick/Electronics-CAD Use...

... 2020 extrusion. Add as many of the 2 arms as you need to get your desired position/angle. It's all held together by some M3x25 screws. Original mount: https://www.printables.com/model/266287-prusa-mini-webcam-bracket-microsoft-lifecam-hd-300

A specially designed printed component provides robust support for the lifecam. ...The pivotal shaft is secured using a 4mm screw, approximately equivalent to 5/32 inches in diameter.

The Human Eyes Only Microsoft LifeCam HD-3000 Privacy Cap Protects Your Private Space

Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. ... Tested on FlyingBear Ghost 5

This is a very simple camera mount for Anet A8 and Microsoft Lifecam HD-3000. ...The mount features an adjustable slider for height of the camera and adjustable Yaw rotation of the camera.

Human: Customizable Base for MS Lifecam HD 3000 Print Settings: Printer Brand: Printrbot Rafts: Irrelevant Details Supports: Unnecessary Features Notes: Slow Down the Print! I sped through at 10 mm/s, but the rest was done at a blistering 50 mm/s.

*Redesigned - Made taller and further outHolder/Mount for Microsoft Lifecam HD-3000 for Neptune 4 Pro.Unscrew left side of faceplate and slide in through grooves.May work with the Neptune 4 and 3 Pro as well. ...From photos it looks like it has similar...

Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. ... Tested on FlyingBear Ghost 5 **Please share Makes and feedback.** **If you liked it consider for a donation.**

This setting disables the video function by closing the camera port. ...I mostly use it as a microphone. Designed specifically for the Microsoft LifeCam HD-3000. :) To rotate this model, turn it 90 degrees on its X axis. ...Thanks and enjoy!

Secure a Microsoft Lifecam HD 3000 webcam firmly within its cage by utilizing three 1/4" bolts. The designed tabs on the back seamlessly integrate with my Linkos mounting system, which also relies on 1/4" bolts for secure fastening. ...With this setup,...

Handy Tripod Support for Microsoft LifeCam HD-3000 A Better Version Remixed by Dmarc73 Check out this design at https://www.thingiverse.com/thing:2917065 Print Settings: Printer Brand: Prusa Printer Model: Prusa Mk2 Rafts: No Raft Needed Supports:...

Mount designed to hold the Microsoft LifeCam HD-3000 inside the Flashforge dreamer on the front left side, 4 x 2.5M screws required to hold everything in place. Main mount doesn't need support, but would recommend support for the wire manager. ... ...

This clever design serves as a straightforward yet ingenious camouflage for Microsoft's HD-3000 Webcams.

The LifeCam clips have been modified from LoboCNC's LifeCam HD-3000 Mounting Bracket found on Thingiverse (https://www.thingiverse.com/thing:2126754). For vision, a 60mm light ring has been attached to the clip using hot glue. To assemble the mount,...

Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. Tested on FlyingBear Ghost 5 Please share Makes and feedback. If you liked it consider for a donation. Print Settings...

One of the cheapest, still good working USB webcams is probably the Microsoft LifeCam HD-3000. You can get them used for as low a 3-4 euros. Attaching it to a printer usually looks messy, so the best way to use it, is to disassemble it and just use...

What you need : 1x Microsoft LifeCam HD-3000 2x M3x12 screw 2x small cable tie Printed parts :-) Printing : - The STL files are oriented the way I think it print best. - 0.4 nozzle, - 0.2 mm resolution, - infill 100% - Support is needed. - I...

I designed this webcam mount to mount my Microsoft LifeCam HD-3000 into my printer enclosure. It is designed to be installed to one of the IKEA LACK table's hollow legs.Installation:Drill a 2cm hole into the LACK's legInstall the “Hole” part, by...

I designed this webcam mount to mount my Microsoft LifeCam HD-3000 into my printer enclosure. It is designed to be installed to one of the IKEA LACK table's hollow legs.</p><p><strong>Installation:</strong></p><ol><li>Drill a 2cm hole into the LACK's...

Easy adapter for attaching Hd-3000 webcam to a 3D printer with a 6mm frame. You can use this design on anything that is about 6mm thick, really. ...I used the guide found at astrophotovideo.wordpress.com/adapting-a-webcam-to-a-telescope/ to modify the...

... the hole. If it's too loose, try adding some super glue on the outside of the nut to hold it in.Check the original for instructions on how to properly disassemble the Lifecam to remove the stand and fit it on the mount.&nbsp;&nbsp;Category: Camera

I've also included an earlier mount that I used which doesn't require taking the LifeCam apart to change the bracket. Google on how to take it apart, it's not difficult, just a bit tricky. Printer Settings Printer: Malyan M150 Rafts: No ...

3-part cover for Microsoft LIfeCam 3000 HD. The parts should all fit together printed as-is (i.e. tolerances are already accounted for), but I'm not sure if the fit on the cam is perfect as I made this for a friend, don't have the webcam. ... Assembly...

MICROSOFT USB CAMERA