haunted 3d

[ ] 3D Print included stl files [ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan case. [ ] sunlu_gauge_ring.stl -- circular slip ring for mounting the hygrometer to the front of the case. [ ]...

I'm still using the 8bit version of Marlin given my driver board, but have had good luck with Klipper 3D - an excellent way to get new life out of your Arduino-based driver board assuming you have a Raspberry Pi hooked up to it. Regardless, taking a...

An individualized adaptation of the 3D printable design found at http://www.thingiverse.com/thing:55821 has been created utilizing Thingiverse's Customizer tool with the thing ID 55821. OR The unique version of the item available at...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress. Shipping takes a while from China but quality is excellent and the prices are...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

See “Large Binder Clip Tentacle Monster” below in connectors.Tentacle Rail Clip BaseThis Tentacle System base includes a clip that attaches to the T-Slots in the aluminum extrusions used in Prusa and other 3D printers. Used in combination with the...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

Use thread lock to ensure these will not accidentally come loose.A 36mm diameter propeller should run freely inside the rudder at all rudder angles.Mount the rudder support to the hull using M3x6mm screws.Then put another M3x6 screw to secure the...

I've spent quite a bit of time getting to this design and I want to make it as accessible as possible so that as many people as possible can enjoy the greatness that is easy loading/unloading of the MMU. Good luck and enjoy!! Print Settings Printer...

Now you can print them out and use them for your nefarious purposes as you travel the far and vast star systems.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

It looks better when printed at that size.Print out and assemble with superglue.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

If you want to add time indicators to the watchface I'd recommend using roman or greek statues holding the numbers, to fit the theme. UPDATE: I've added a few statues with numbers to make reading the clock a little easier, they are based on the...

Remove the z-axis tops and replace with this light bar mount. Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired...

Potřebné vybaveníNotebook nebo tablet, programy Tinkercad a PrusaSlicer, 3D tiskárna.Nepovinné - krabička čtvercových rozměrů, tvrdý papír, pravítko, tužka a nůžky (viz postup).9. Potřebné soubory a dokumenty (seznam...

If you don't own a 3D printer but have seen this blank somewhere else and want to use it, I recommend just asking in a furry group chat on a platform of your choice. Many furries are also tinkerers and will print this for little money.</p><p>The base...

Operated with a driver or remotely/programmatically with an AI, much of the work performed in the Space Port can be automated.Reducing risk.Eliminating squishy biological beings.Increasing efficiency and profits!Upscale your space port, eliminate...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

It's yours to make!).Stand up your Space Port before it's too late!&nbsp;More Space Port!Space Port - https://www.printables.com/model/205432-space-port-terrain&nbsp;Space Port Living Quarters -...

I also added a version of the female parts with a tolerance of 0.2mm for those who have well tuned 3D printers (see below). To know more about your Printer tolerance, don't hesitate to have a look at <strong>Maker's Muse</strong>'s videos on the...

These strips are bright enough I didn't notice only one was on. View from Octoprint Control tab during the first layer of my first print after installing. Print instructionsCategory: 3D Printer Accessories Summary Prusa i3 MK3 PiCam v2 X-Axis Motor...

You only need the USB board and the motor to make it run.This was specifically made for making interactive 360 photos of 3D printed objects quickly, using video (takes about 10min), but it can also be used for making animated gif's, rotating objects...

... layers, 60° bed temperature, outside perimeters first. &nbsp;I turned the model 35° anticlockwise, then set the seam position to ‘rear’. &nbsp;The texture on the side panels comes from this textured bed plate, and I used the Tecbears black PLA.

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

It appears to be a set of points in 3D space represented using an [Hull format](https://docs.python.org/3/library/pickle.html#pickling-hints). I will assume you'd like me to convert this into some kind of array. However, there are no "lines" or...

Possibly by using simulations.Rails as a wholeSince my 3d printer is not big enough to fit 120cm ring on it (its bed is 210x250mm) I needed to split rails for printing and connect them afterwards. I decided on using M5 bolts and nuts.</p><figure...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...