hatchbox pla settings 3d models
899974 3d models found related to hatchbox pla settings.
thingiverse
The basic idea is to print 3 rings and then insert them to the inside of a hatchbox (or similar dimension) spool, then the spool can be used to hold smaller cables like Ethernet, HDMI, power cables, etc so they don't get mixed together. The...
thingiverse
This is my final fan shroud upgrade to replace the stock one that came with the Hatchbox Alpha. I designed it with a smaller, more focused airway that concentrates airflow closer to the print head for better cooling results. Additionally, I wanted to...
thingiverse
... with nuts on the bottom side preventing friction between the drawer and the spool. Print Settings: Printer: FT-5 Rafts: No Supports: No Resolution: 0.3mm Infill: 10% Notes: Printed at 70 mm/s in PLA using a 0.6 nozzle, showcasing optimal results.
cults3d
Customized version of https://www.thingiverse.com/thing:2111353 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2111353 for GEEETECH PLA Spools 1kg
thingiverse
... Implemented. ...* The Groove Mount Interface Was Thickened by 0.5mm for a Tighter Fit. Printing: I Printed This Part in PLA+ with 100% Infill at 200um Layer Thickness. ... Revision: v1 You'll Need 2x M3x15ish Screws to Attach the Two Pieces Together.
thingiverse
Here's a completely redesigned elliptical gear set compatible with PLA, featuring herringbone gears that perform exceptionally well when printed in PLA or ABS. I deliberately avoided working on the traditional elliptical gear design due to its...
thingiverse
Instructions Utilizing the Following Options to Craft Your Dream Design: Number of Teeth on Planets Set at Six Width Parameter: A Crucial Six Point Seven Units Polar Angle Value is Set Precisely at 45 Degrees Torsion Value Measured at Exactly...
thingiverse
......http://www.thingiverse.com/apps/customizer/run?thing_id=431426 Instructions: Using the following options: Height is set to 8 inches. Rod diameter is 15 mm. Diameter is 55 mm. Number of legs is 3. Overall height is 29 inches. ...Leg thickness is 3 mm.
thingiverse
... M8 threaded rod. ...Inner diameter: 7.8mm Outer diameter: 54.8mm The inner hole is a little bit tight but after some moving on the threaded rod it works just fine. Print settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.15mm Infill: 30%
thingiverse
Now go make one with a small spool hole of 35.7, a large spool of diameter 85, unit count as above but set this at the end. This makes the new parameters used: spool_width = 65 spool_hole_diameter = 35.7 unit_count =1 As said earlier the main...
thingiverse
I have created a fully compatible elliptical gear set in herringbone gears using PLA material. I was unable to work with the original elliptical gear design because the pins kept breaking off when printed in PLA and ABS. This new design, however,...
prusaprinters
2m of 1.75 filament) This pack contains all / most models for the Polymaker polyterra PLA filaments. Pack contains:Polyterra PLA - Army BiegePolyterra PLA - Army BluePolyterra PLA - Army BrownPolyterra PLA - Army Dark GreenPolyterra PLA - Army Light...
thingiverse
Custom Section: Retract Settings: Using 1.75mm filament as default: Travel speed = 175 for all Cool min layer time = 15 for all ABS: Retraction speed = 10 Retraction amount = 1 Retraction dual amount = 16.5 Retraction min travel = 1.5 Retraction...
thingiverse
Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3243306 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3243306
thingiverse
Customized version of https://www.thingiverse.com/thing:5640914 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5640914
sketchfab
The glTF Point-level Animation Test is a key benchmark for evaluating the performance of 3D graphics rendering software and hardware systems. This rigorous evaluation methodology involves pushing the boundaries of animation complexity, mesh density,...
thingiverse
I can create content, however, I must remove foreign characters first. Customized version of http://www.thingiverse.com/thing:148722 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=148722 Using the...
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358
thingiverse
Customized version of https://www.thingiverse.com/thing:3417919 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3417919