hasselblad 500 el m 3d models

You can now unlock your Hasselblad 500 EL/M Battery door without needing a coin or screwdriver. Simply use the folding handle to open it with ease. Printing this lock on an Ultimaker with the highest quality setting and a reduced speed of 25mm/s...

To convert a motorised Hasselblad with a manual knob for film advance and shutter cocking. Not an easy modification, please consult the guide.04/12/2023. Edited "shutter trigger.stl" to properly trigger the signal flag on the film back. Changed...

Template for (laser-)cutting your own replacement leatherette for the body of an old Hasselblad 500 EL/M camera. Print instructionsWhen lasercutting thin leather, I'd recommend taping it to a piece of MDF using double-sided tape, so it wont curl,...

Introducing a custom lock for your Hasselblad 500 EL/M, eliminating the need for coins or screwdrivers. A new version of this knop features a slightly larger hole for improved fit. Optimal printing results are achieved on an Ultimaker at 25mm/s speed...

Create your own real leather replacement for a Hasselblad 500 EL/M's body by following these steps. After winning an auction for a functioning Hasselblad 500EL/M, I replaced its fake-leather with authentic leather sourced from a local tannery. After...

This is a custom made handle/battery-door lock for the Hasselblad 500 EL/M, which does not require a coin or screwdriver to open. Print instructionsPrinted the parts using PLA with a layer height of 0.2mm. The holes in this design are the tricky...

A replacement part is needed for the plastic screw-like component of a Hasselblad 500 EL/Ms battery door, following a broken plastic piece due to a damaged battery adapter. The process involved measuring and numerous attempts. After removing the old...

I measured the entire camera with a simple ruler and a lot of guesswork. Then I recreated the dimensions and shapes in Inkscape. After many test-prints on paper, these are as close as I could get to the real measurements of the camera. The parts were...

A battery adapter for USB for the popular Hasselblad 500 EL/M V-System camera. There are a few expensive battery adapters on the market that use AAA-batteries but this one uses USB power from a powerbank to power the camera. The principle is to...

A reproduction of the beautiful Hasselblad 500, a medium format film camera made by Hasselblad and produced in the 60s. Fully 3D printable. ...Remember to Scale and Print

The photographer relies heavily on the versatility of the Hasselblad 500 cm coupled with a high-quality 50mm f/4 Zeiss lens, capable of delivering exceptional results under various lighting conditions.

a low-detail model of the Hasselblad EL and astronaut mounting plate. it's full scale, I just look at the printed astronaut's chest plate and mark how wide the camera would be, then scaled the width of the model to that. two versions of the adapter...

A scaled-down Hasselblad EL model, complete with an astronaut mounting plate, takes shape. The printed chest plate of the astronaut serves as a guide for determining the width of the camera. This width is then scaled to match, ensuring accuracy in...

These are masks to place against the curtain on the back of the body of a V series Hasselblad to capture 645 images (in either portrait or landscape orientation) and 6x3 "panoramic" images. I printed and sanded down to exact fit for my camera. ...These...

Convert your hasselblad 500el/500elm to manual cameraneed M2*12 and M2*6 extra screws

Convert your hasselblad 500el/500elm to manual camera need M2*12 and M2*6 extra screws

A 3D design for a pinhole camera transformation of a Hasselblad is planned by me. ...The process involves printing the camera, drilling a 1/4 inch hole at the center of the lens, covering it with tinfoil and poking a small hole, or removing the front...

This is a cradle for dry plates on a Hasselblad 500 or Kiev 88 camera. ...To assemble it, you'll require a light-tight sheet from a film pack and three magnets with a diameter of five millimeters and a height of three millimeters.

This low profile adapter is solely optimized for the Lime Two light meter to be mounted on a 500 series Hasselblad camera. ...If you want to use it with other accessories you probably have to adapt the STL Update July 2023: current updated variant!

I'm a Text Rewriting Bot.

Use 9V block battery to drive hasselblad el series. Need two M3 screw and a battery cable to work with. DO NOT USE CHEAP BATTERY. It takes high current to drive film back. Cheap batteries could work with the body itself but will not provide...

Rear cap for Carl Zeiss Lenses for the Hasselblad V-System.

Rear cap for Carl Zeiss Lenses for the Hasselblad V-System. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 15% Filament: Prusament PETG Category: Camera

Viewfinder mask for the Phase One H20 and P20 digital backs when used on a medium format Hasselblad V system camera, like the 500 C/M, the 500 EL/M, and many more models. The H20 and P20 both use Kodak's KAF-16801CE sensor with a dimension of 36.9...

The M SUPERCAR design emphasizes a contrast between its upper half, characterized by soft edges and rounded contours, and its lower section which is boxy and edgy. ...This separation extends to the finishes; street cars boast painted tops and carbon...

Here's how you can make your own custom camera strap lug, without breaking the bank: first, design and print the part with a fill rate of 50%, so it has the right balance of strength for its tiny size; this may take some trial and error to get right...

MoinIch habe eine kleine Box zum sicherem Lagern der Air Gear Pro M-500 Maske angefertigt, mit Belüftung schlitzen auf der Unterseite und neben Fach, um Ersatz filter zu lagern. Die Box hat die Maße 230 mm, 180 mm und eine Höhe von 110 mm, der Deckel...

Objective Focus System for Hasselblad Cameras; Ultimate Lens Solution for Hasselblad Lenses

Remixed from Hedeco's Lime Two low profile mount, but this will fit Doomo's S line of meters.Enjoy!