harmony hub mount 3d models

You can hammer it into place on the wall perhaps someone will find a use for it. ...It pairs well with this USB 3 Hub: http://amzn.to/2j7z5R9

... rotate one of the nuts, so make sure you rotate it into place the correct direction. (One goes on CW the other CCW.) Made to fit a 16 port i-Tec USB hub. (Specifically this one: https://www.multicom.no/i-tec-usb-30-charging-hub/cat-p/c/p1000039985)

... by @piercet and https://www.thingiverse.com/thing:3844416 by @Bitterbuffalo. ...I wanted to replicate the rotation of the Google Nest Hub, but without the support underneath the speaker. ...This remake achieves that goal, and I hope you enjoy it!

Holder for a USB-Hub secured with screws. Dimensions: 45mm x 24mm x 10mm. Screws hold the device in place through: 4mm and 8mm diameter holes, 3mm deep. This design marks my first upload. ... I look forward to seeing if it meets someone's needs and...

This is an uncomplicated casing designed with two screw openings that allow you to fasten a D-Link 7-port USB hub in diverse locations such as beneath a table, on a wall, or any other suitable place of your preference.

I had a cheap Sabrent HB-MCRM USB hub (4-port) to fix the problem of my Orange Pi Zero2 only having 1 USB port without getting an expansion board.I printed with TPU and this works well, however my edges came out a little sloppy due to wet...

There's a specially designed clamping solution available on the website at www.h0fine.com, specifically crafted for use with the fully assembled LoConet Hub PCB. ...The clamp boasts a wall thickness of precisely 12 millimeters, ensuring a secure fit for...

Simple wall hanger for a Seagate backup plus hub external hard drive. Leaves a lot of room for air flow. Built heavier than needed because I didn't want to risk a $300+ hard drive falling. ... .STEP and .f3d files included.

... - a hole in the back. ...This particular design choice allows for an additional power connection via micro-USB, which is a common requirement for some USB hubs. ...You can find the Fusion 360 file for this project by visiting https://a360.co/2CsScBc.

Simple print for a 8 port D-Link USB Hub (99 x 67.5 x 26mm) with intergrated cable winding / tidy channels. ... First print - things I would change for next time; 1) Thicker walls and tabs for the attachment points 2) Drop the 4th tab in front...

* Cutouts in the hex shaft allow screws to pass through and secure the Pitsco hub to the printed adapter. * A raised platform for the hub positions it above screw heads. ... Suggestions: * Print with axle horizontal to enhance strength * Be prepared to...

This is simple remix for mounting Power4Hub by Teknic to standard DIN rail.

Not much to say... ...It's a pegboard mount for a mutiport charger.

Have put the hole on the left side so that this can be mounted nicely by means of cable duct.

... mount can should be fixed with screws to withstand USB plugs being pulled. ... Screw head size max 6 mm Screw thread size: max 3,5 mm. Screw head could be coned or flat. After mounting it, slide the entire dock into the two wall mount pieces. ...

To provide a secure surface for the device, a custom-made mount was created. This eliminates the need for sticky tape that may not adhere properly to the original unit's back. ...The mount can also accommodate screw installation by drilling a hole in...

Wall mount can should be fixed with screws to withstand USB plugs being pulled. ... Screw head size max 6 mm Screw thread size: max 3,5 mm. Screw head could be coned or flat. After mounting it, slide the entire dock into the two wall mount pieces.

You can customize the length, height, thickness and mount type.It's my first time using OpenScad, so I apologize for any shortcomings, or poor quality code.The Honeycomb Storage Wall (HSW) uses the HSW Library. ...You can comment the lines if you're...

Philips Hue Gen 2 UK plug socket mount with cable tidy box. ... Cable tidy box connects to main body with 8mm x 2mm magnets (8 in total)

I wanted some USB outlets mounted under my desk near the front on my new desk as it height adjustable and i have mounted the tower underneath and accessing the USB ports is a bit more awkward. I wasn't able to find anything i liked so i bought a...

I retool this design by incorporating versatility into the mount, allowing it to securely fasten to a variety of planes including vertical, horizontal, and angled surfaces.

... are 5mm radius fillet. ... This thing is designed to hold the charger and resist the forces involved in plugging and unplugging USB cables Mounted with 4x 6G wood screws Printed with PETG on Anycubic Mega S, 40% infill in either box or cubic pattern

I modified the original wall mount because I felt the print time and size were excessive for its purpose; I also didn't want to risk printing the original and struggle with my current ethernet cables. After printing, I mounted the new version on the...

I successfully mounted the LED on top of my Alfawise U20 (CR-10 clone) using Kay82's versatile holders, which can be found on Thingiverse under ID:2470737. To complete this project, I needed to carefully arrange the wires, ensuring that there was...

https://www.amazon.de/-/en/gp/product/B082SQT12J/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 It is attached to the wall with two Ø6 fisher screws.This mount also has cable slots for cable managment. Printed with bottom side down such that...

Hi everyone, I'm excited to introduce my Google Home mount that attaches securely under your cabinet without needing any additional support. If you have any questions or need further clarification, please don't hesitate to ask. ... For those interested...

This mount fits the IKEA TORNLIDEN: http://www.ikea.com/us/en/catalog/products/40240625/ Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Mini Rafts: Irrelevant Supports: Unnecessary Resolution: 200 Micron Infill: 10% Post-Printing...

Hub made for Bi-Cycle All dimension are approximate.

A tyre hub for go-kart and efficycle

time pass just a crude 3d model of hub