harmonic drive mount 3d models

https://www.amazon.com/gp/product/B08V8MSWZM/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1 I am not affiliated with this product in any shape or form Product arrived, no bltouch mount. Seller sent garbo file. I am better than that Open inventor.exe...

This is a work in progress and will be updated as I finish my build and dial in the part.No hardware direct drive extruder mount for Ender 3. This model uses the v-roller spacers and x-carriage for mounting. ...The extruder motor is spaced for use with...

This is a straightforward hard drive fan mount with a slight tilt.\r\nIt's designed specifically for 3.5-inch HDDs and 120mm fans.\r\nI created this fan grill because I needed something like it for my project, but I know it's not the most practical...

This is a mount for the Drakon geared extruder, inspired by the Speed Drive mount (https://www.thingiverse.com/thing:3816051). My goal was to reduce the weight of my direct drive setup by using a smaller stepper motor in combination with a geared...

What you need: - Klemco Mount - M3 Screws (come with Klemco Mount) - BMG Extruder - Dragon (HF) Hotend (or other Hotend with grove mount eg. ...E3D V6) - Short piece of PTFE tube - NEMA 17 pancake stepper (original stepper can also be used) Have fun...

I've printed two direct drive mounts for my LK4Pro. And even though they have been described as dedicated to LK4 PRO, both of them were not aligned properly. In my case they are about 1 mm too much to front and about 2 mm too much to the right. ...

I ran out of space in my case to hold Hard Drives so I came up with the idea for a dummy PCI card that lets me mount 3 2.5" SSD's in an unused PCI slot. Print Settings Printer: Flash Forge Creator Pro ...

This is a remix of the Speed Drive direct mount to fit the Kobra Max. Everything fits well and doesn't flex unnecessarily. This is designed to fit the stock stepper motor and extruder. I replaced with a pancake stepper to reduce weight. To...

I designed this direct drive mounting bracket to use the stock extruder and mount it on the x carriage so I could print TPU without any purchased modifications. I did use a short length of Capricorn tubing between the extruder and hot end, the stock...

The direct drive mount is suitable for the original stepper including extruder Stepper motor is a >Nehma 17< Attention!!! Other stepper motors like Creality will not fit here Furthermore, cable extensions are needed to extend the lines. 4 times...

It's ment to be used without the bowden coupler on the extruder This is a direct drive mount for the Bullseye V6, with stock extruder and stock stepper motor. I have yet to try it out, but it's modeled in Fusion360 using Ender-3 step files along...

Uses the PCMCIA TV slot to support the hard drive in the back of the TV Utiliza la ranura PCMCIA del TV para soportar el disco duro en la parte posterior de la TV

The design is versatile and should fit other external hard drives as long as they match the specified dimensions. Fusion 360 was used for the design, showcasing my self-taught skills in the software. ...Although still learning, I'm proud of the...

This design can be used to prop up your hard drive onto the back of the laptop screen so it has a place to stay while you use it!

I made this to hold a dual H-Bridge DC motor drive module. After printing, I drilled/tapped for M3 screws to attach the motor driver. ...Motor Driver from Amazon:https://a.co/d/aClSjp7

Human: Bush for installing a hard drive in a HP enclosure Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 100%

I needed an external storage device for my gaming console's digital collection, so I created a custom housing to cradle the hard drive and attach it to the PS4 when it's standing upright. The design consists of two printed parts that are then bonded...

The File for the sv01 stock direct drive plate did not work, made it so you can use 3 of the stock screws and made it longer so you can use the bottom left. No instructions or support... ...Well if you want to pay for it lol Stock extruder

Mount for BMG extruder for Z-Bolt 3D printer with CoreXY cinematics. ... Requires four M3*35 crews.

I made the same STL file as before, but I enlarged the mounting holes on the extruder so that it can accommodate offset Bowden couplings.

I made it cheap as possible and easy to install with uses stock extruder and stopper. ...Might required some longer bolt on gantry mount and stepper.

This is a remix to add a hole for the fan shroud mount and a cut out section for the CR Touch screw.

As you know, if the HD disconnects while the unit is on, it can result in significant data corruption.As a solution, I designed a simple cage that holds the HD &amp; hooks onto the top ridge of the PS5 side plate keeping the drive safe and in place.I...

Direct motor mount for Sunu's extruder. This was designed as an easy quick fix as the PETF tube end broke off. ...I am working on Artillery sidewinder hot end fit - Testing in progress.

First, unplug the extruder motor, then take out the motor and install it into this mount (you'll have to enlarge the screw holes a bit). Redesign the extruder wire so that it goes straight to the hotend. ... Use approximately 1.5 inches of PTFE tubing...

I encountered problems printing TPU with the standard setup because of the space between the mount and the bottom of my extruder, so I modified it by adding a guide that fits snugly into the extruder's outlet after being lightly sanded.

The original file was almost perfect, but I did find the mount too loose in my channel. I remixed this and now it is a tight fit. I had to use my rubber mallet to lightly tap it into place on my rail. ... The rotating ball fit my 1.75mm...

Adjusted to fit dual gear metal extruder with no bend in the filament tube and mount for filament runout sensor. you may need longer screws for the sensor and a couple of pieces of Bowden tube as spacers. This is a work in progress. ...It is working...

I fabricated a mounting platform for Greg's Wade extruder specifically tailored to fit the Prusa i3.\nAlso, required components include:\nExtruder hardware can be found here: https://www.thingiverse.com/thing:43411\nMotor support hardware is...

... end and a BMG extruder. Fully compatible with the official BLTouch mount. ... A tremendous thank you goes out to Ross Korsky who created the X-Carriage model: https://www.thingiverse.com/thing:2789191 that I used as inspiration to design my part.