harbor freight magnetic strip 3d models

I was looking for a way to add a magnetic tool holder to my K1-Max, Harbor Freight Item Numbers : 60433, 65489, 61199, 62178, these are what I came up with. Your choice : one for 3mm, 4mm, or 5mm heat set inserts (the 5mm may work best). I used the...

Remixed to fit Harbor Fright tools Long powerstrip.

Mounting a handy power strip just got a whole lot easier thanks to Harbor Freight's innovative 12-Plug Power Strip Mount. This nifty accessory adds an extra layer of stability to your power strip, making it even more robust and reliable. ...Plus, with...

Both items can be easily purchased at Harbor Freight Tools. The brackets stand at an impressive 66 mm tall, providing ample space for versatile mounting options. They can be installed along the front or rear face of the wooden workbench, allowing...

Mounted the 4-foot power strip on a table measuring under four feet tall by printing out a custom mounting bracket from scratch.

This is to adapt a Harbor Freight magnetic base to a 1/4-20 thread for mounting mics, cameras, and other things to it. ... Watch This Video to see what it's for https://youtu.be/oca56SyahMQ

Just a quick cap I made to cover the ends of the Harbor Freight Magnetic Hooks. Print with a Brim just to help it adhere to the bed, since it's so small. I did 4 at once with the brim. ...Print with the hole facing up.

You'll need a Harbor Freight magnetic base (or grab one on Amazon, assuming the rod sizes are the same), 1/4-20 threaded rods and nuts for it....oh yeah, and a GoPro. ... Assembly and ideas for usage can be found in my YouTube video for this project at...

I picked up a magnetic tool bar from Harbor Freight [(item # 60433)](https://www.harborfreight.com/18-in-magnetic-tool-holder-60433.html) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall...

I picked up a magnetic tool bar from Harbor Freight (item # 60433) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall studs. Sure, I could use wall anchors, but what fun is that when you have a...

I picked up a magnetic tool bar from Harbor Freight (item # 60433) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall studs. Sure, I could use wall anchors, but what fun is that when you have a...

A versatile tool holder, specifically crafted for the Harbor Freight magnetic tool strip. This design complements my previous creation, a rectangular tool box available on Thingiverse: https://www.thingiverse.com/thing:3564947. To assemble this...

I love the 18in Harbor Freight Magnetic Tool Holders. I have several in my garage and office. I recently dropped a big thing of small screws and nuts and most magnetic sweepers are way too expensive for me for occasional use. Harbor Freight has a...

Just something I threw together to mount all the 4 outlet power strips from Harbor Freight that I've collected over the years. ...The mounting holes are 6mm and fit a #8 screw really well.

This is a magnetic bit holder for a Harbor Freight Bauer 20V drill or driver. It uses two 8x2mm round magnets that you must glue in. ...The holder has two 15mm deep hex slots for shorter bits and can hold a long bit or drill bit on the outside.

Printed in PETG+, I remixed the original design from user Samhyamss to accommodate the slightly larger dimensions of the Magnetic Tool Holder from Harbor Freight. ...Fit is snug and filament should just barely stretch to fit the clips into the Skadis...

hotbrass created an incredible dual-flashlight housing using two free Harbor Freight flashlights. This clever design eliminates the frustrating button that switches between the intense bright light and the weak, nearly useless one, instead adding a...

Ahegao handle for harbor freight workbench drawer.

Replacement slide on 3/8 drive socket holder insert for the Harbor Freight magnet organizer. ...Friction fit rather than ball bearing snap but it works fine.

... ... printed with the flat side down. designed to be affixed with a 3m command strip. harbor freight screwdrivers like this have really poor quality control so you may need to clean up some plastic over-molding on the screwdriver to perfect the fit

A custom enclosure is built to hold a Harbor Freight multimeter securely in place. ...Additional storage compartments are integrated into the design, allowing for magnets to be stored within easy reach.

A box and lid to securely hold set of Harbor Freight Probes. ... There is a remix that is a box for mini files from Harbor Freight as well.

I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.

I think this is the medium size vice from Harbor Freight best printed out of TPU.

I created a Harbor Freight flashlight holder that lets me illuminate the dark spaces around my machine at work when I'm swapping tools. This design relies on five millimeter by five millimeter by three millimeter thick magnets for its stability.

I created this Harbor Freight flashlight holder to illuminate tight spaces when changing tools on my machine at work. The holder utilizes 5mm x 5mm x 3mm thick magnets for secure attachment. ...I've also made available the Fusion 360 file, allowing...

An assembly fashioned utilizing materials provided by 80/20, Inc. ...to accommodate my Harbor Freight metalworking tools including a shear, brake and slip roll.

You can easily upgrade the free Harbor Freight LED by swapping it with an 18650 battery, taking advantage of its similar 3-volt output to standard AAA batteries.

This is a red diffuser for a Harbor Freight flashlight. I needed to use my flashlight at night while keeping my night vision. ...

Quick socket organizers I made for harbor freight deep well socket sets. ...I've included a file for both SAE and metric sets.