happymodel mantis85

Antenna holder for Happymodel ELRS 2.4G receiver. Printed without support. Attached to double-sided tape. ... To fix the antenna whiskers, I used ear sticks + some glue

I've created a range of them to go on various standoff diameters and distances (center-to-center): 5 x 19 = QAV-S 5 x 20 = Switchback 5 x 22 = Nazgul 5 x 23.5 = Source One V4 / HD / Apex 5 x 24 = ImpulseRC Apex 5", 6", 7" 5 x 24.5 = Fywoo Explorer...

I stumbled upon an existing design for the Larva X canopy from Happymodel and made significant modifications to adapt it for 3D printing, specifically targeting weak points to boost overall durability.

Happymodel Mobula7 1s tinywhoop open prop conversion frame inspired by the flywoo firefly nano baby frame. Weighs about a 4g, 1g lighter than the happymodel ducted frame. Very strong, pretty much will never break as this frame with the mobula7 1s...

I'm looking to create custom support for the camera on my Happymodel Trainer66 mini-drone. ...The standard support that comes with the drone isn't compatible with the camera included in the package, so I've decided to make a personalized piece instead.

I shared them at https://www.happymodel.cn/index.php/2019/09/16/3d-printed-insulating-tpu-board-for-larva-x-insulating-between-the-fc-and-the-diamond-vtx/. ... You can also check out this review: https://blog.whichfpvkwad.com/2019/09/19/review-larvax/.

Whoop Frame for Happymodel Larva X drone is designed with screws included in the purchase package. Testing has been successful, but modification may be necessary. There are two models available: one for Larva's with 3 screw hole motors and another...

ExpressLRS happymodel 915M TX JR module case

This is mini Antenna holder for Happymodel Crux35 Good luck

Works with all happymodel style 2.4ghz T-antennes. ... printed in TPU

Happymodel Larva battery mount with support helps with a square and level position for take-off

This is a adjustable angle mount/clamp for the Mantis85 quad that attaches to the SQ11 and SQ12 mini HD cameras. Bare in mind it does not protect the camera in any way just holds it in place. it works in conjunction with the the clip bellow....props...

I cloned the stock Happymodel Crux35 camera mount and modified it to better fit a Geprc Naked GP8.

I have 2 ExpressLRS mounting options on my AOS LR5 O3 build. ... These are sized for the Happymodel ELRS antennas.

This is a mount I designed to mount the Happymodel EXPRESSLRS EP1 DUAL on a standoff. ... Printed in TPU.

This is an adjustable angle mount/clamp designed for the Mantis85 quad, specifically made to attach to both SQ11 and SQ12 mini HD cameras. It's essential to note that this mount does not provide any protection for the camera; its sole function is to...

Happymodel EP1 ELRS antenna mount for Geprc Mark4 and clones. Use 2,5 mm zip tie. ... Fix to the frame with E6000 or similar glue.

Simple remix of haku3d's awesome folding TPU holder for the happymodel EP2 receiver. ... Remix does not require nuts - the screws screw right into the TPU.

Reworked the Happymodel STL to reduce vibrations. Print on the side for an easy print. ...One of the models have a built-in structure which helps in case your printer have poor bridging performances with TPU.

https://youtu.be/FjhCgxlCpMo I made this for my Happymodel Cine8 and Caddx Peanut. You can fit the charger on the camera without removing it from the mount. Removing supports does suck, but it;s a lightweight design. ...

Direct downloads from my website: http://www.haku.co.uk/3D/Happymodel_EP1_plain_holder.stl http://www.haku.co.uk/3D/Happymodel_EP1_16x16_holder.stl http://www.haku.co.uk/3D/Happymodel_EP1_20x20_holder.stl...

Direct downloads from my website: http://www.haku.co.uk/3D/Happymodel_ES900RX_plain_holder.stl http://www.haku.co.uk/3D/Happymodel_ES900RX_16x16_holder.stl http://www.haku.co.uk/3D/Happymodel_ES900RX_20x20_holder.stl...

The Happymodel Crux35 FC 20x20 holes are not centered so changing to any other FC may be an issue. I have built this adapter plate which moves the 20x20 holes a bit to make the holes match the desing of the HGLRC Zeus 35 AIO F4 flight controller.

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.</p> ...

not really a remix but a redesigned hard canopy for the happymodel moblite inspired by angry don's version. print in PLA flat to the build plate using supports for the optimal structural strength. only 3 screws needed. ...weights about ~1.2g.

I narrowly avoided losing my MicroSD card during the initial test of Happymodel's Diamond VTX with a Toothpick.\r\n\r\nGiven that the unit itself doesn't include a lock for securing the microSD, I created this basic design.\r\n\r\nPrint it using 100%...

Remix of Happymodel EP1 ExpressLRS folding TPU holder by Haku3D to include a 3 point mounting option for 25.5x25.5 Whoop pattern. I made this to save height space when using an OVX303 VTX and to align the EP1 in the direction that I wanted. ... ...

Happymodel 2.4GHz ExpressLRS ES24 TX module slim adapter for TBS Tango2. ES24 TX module is for JR bay. I put it on my Tango2 slim bay. Instrtution is available in PDF format : ES24Tango2Adapter.pdf I reused the STL file from '2.4GHz Slimer TX...

Direct downloads from my website: http://www.haku.co.uk/3D/Happymodel_EP2_plain_holder.stl http://www.haku.co.uk/3D/Happymodel_EP2_16x16_holder.stl http://www.haku.co.uk/3D/Happymodel_EP2_20x20_holder.stl...

This is a revised version of the original frame:\r\nhttps://www.thingiverse.com/thing:3563189\r\n\r\nMade several adjustments for the motor hole pattern, specifically tailored for Happymodel motors. The battery holder brackets were reworked to...