happymodel mantis85

... so no need for inserts although they could easily be added. The T holder fits the antennas I have lying around but will likely need to be modified to have a smaller hole for Radiomaster and Happymodel ELRS antennas if you're going for a snug fit :)

There's one for HappyModel, and JHEMCU port spacing which has the USB port further in board, and there is one to accommodate boards with the port further outboard (near the edge,) like the FPVCycle 1S 2 in 1 FC/ESC, the EMAX Nanohawk 4 in 1 AIO, and...

Specs of the frame are as follows: * 84mm motor to motor * 6.6mm M1.4 three hole motor mounts * 25.5x25.5mm M2 FC mount * weight ~5.6g (2.5mm CF) My build has the following specs: * JHEMCU Play F4 1-2S AIO * URUAV 1102 10000 KV motors * Caddx Baby...

The frame is a Mobula7 v3 (75 mm frame) The screws are M1.6 X 12mm https://www.amazon.com/MroMax-Machine-Stainless-Phillips-Cabinet/dp/B07YFMTXSS/ref=sr_1_4?dchild=1&keywords=12mm+M1.6&qid=1620660447&sr=8-4 The motors are happymodel EX1102 13500KV...

**Recommended Parts List:** KababFPV Toothpick Frame (8g) GepRC Gep-12A-F4 Flight Controller (5.6g) or Crazybee F4 Pro V2.1 (4.2g) AMAXinno 1103 7500kV Motor (3.8g x4) Unify Nano Pro32 VTX (1g) or Happymodel Mobula 7 VTX (2g) FrSky R9 mini (1.1g)...

... below) I printed the frame with 100% infill to give it more rigidity. ...The frame is also slightly thicker than the original carbon fibre one, which was about 2mm. This frame is 3mm to leave enough room for the screws to grip the motor mounts.

Wingspan: 40cm **AUW: 40g** (with two 250mAh 1S HV batteries) CG calculated by using Flying wing CG calculator Parts needed: - FliteTest 5mm foam board - 0.8mm piano wire or such for servo links - 2pcs 1.7g servos - 2.4G 8CH D8 Mini FrSky Receiver...

There's one for HappyModel, and JHEMCU port spacing which has the USB port further in board, and there is one to accommodate boards with the port further outboard (near the edge,) like the FPVCycle 1S 2 in 1 FC/ESC, the EMAX Nanohawk 4 in 1 AIO, and...

Rc/FPV Equipement for which the parts are: Matek F765-Wing with M8Q GPS QMC5883 Compass, ELRS (happymodel) system receiver, EMAX xa2212 820kv (35x35 holes for motor mount), 10x6 folding prop, 2x Sg-90 9g micro servos, Eachine 1000TVL 1/3 Camera,...

10mm lens diameter Use two short M2 screws to hold Camera mount part 1 and 2 together (M2*3, M2*4) Motor mounts for 070x motors, 080x with 3-hole pattern should also fit (I am using HappyModel 0703 KV19000) 110x version for standard 110x 4-hole...

There is a cut to specifically accommodate the camera plug from the board Happymodel F4 X12, wich is probably the best one you can use. I also added several reinforcements near the motors and moved the four holes to have a better fit for most flight...

Those lipos: https://www.banggood.com/5Pcs-URUAV-3_8V-450mAh-50100C-1S-HV-4_35V-Lipo-Battery-PH2_0-for-Emax-Tinyhawk-Happymodel-Snapper7-p-1387485.html?p=NP17171510059201504Q&custlinkid=107516. Added version with no logo. ...Added version for 2S lipos...

Here are the parts I used in my build: * Beta65 Pro Frame with the low profile mod * BetaFPV 1S flight controller * BetaFPV Z02 AIO cam & VTX * Happymodel SE0802 22000KV motors * GNB 300mAh 1S HV batteries The case needs two strong magnets, each...

It has a horizontal mount that fits a standard Happymodel ELRS 2.4 dipole antenna. Due to the design of the HM antenna, making a solid and reliable mount that does not cover the feed point or active elements with a lot of plastic is not possible. So...

The file is [battery-holder_whoop_1s_TPU.STL] from https://www.thingiverse.com/thing:4231097 Purchasing parts - Frame: Happymodel mobula7 V2 - Flight controller: BETAFPV Brushless Lite (Silverware) 1S - Motors: brushless 0802 (choose anything you...

(1: Rear-R, 2: Front-R, 3: Rear-L, 4: Front-L) Purchasing parts Frame: Happymodel UR65 or mobula6, BetaFPV Beta65 Pro Flight controller: BetaFPV Brushless F4 1S V2.1 or Brushless Lite (Silverware) 1S Note: Brushless F4 1S V2.1 needs to flip 180 roll...

**VTX+DVR combos** * NamelessRC D400 VTX+DVR * Eachine TriangleD VTX+DVR * HappyModel Diamond VTX+DVR **5.8 GHz Antennas** * Lumenier Micro AXII Shorty u.fl: A 1.6dBi antenna for FPV systems. * TBS Triumph Pro u.fl: Another high-performance antenna...

The HappyModel Mobula 6 is an outstanding little whoop-sized quadcopter that meets my needs perfectly, but unfortunately, it doesn't come with a case. To fill this gap, I designed a custom case that holds six batteries, multiple props, several tools,...

10mm lens diameter Use two short M2 screw to hold Camera mount part 1 and 2 together (M2*3, M2*4) - Motor mounts for 070x motors, 080x with 3 hole pattern should also fit (I am using HappyModel 0703 KV19000) Also fits 110x standard 4-hole pattern...

This is an all-in-one mount designed specifically for the Caddx Turbo EOS2, Happymodel Diamond VTX, and a convenient antenna holder attachment compatible with the Mobula 7 V3 frame. The antenna mount seamlessly integrates into the LED holder at the...

This is a remix of the HappyModel Moblite7 canopy that I have adapted for use in an inverted Meteor65 build. In my case I have used a CrazyBeeF4 Lite flight controller from a Mobula6, but other CrazyBee variants would work as well. I have increased...

Alternatives do not fit the 3d-printed frame properly.I broke 5 motors before realizing I was using screws too long for the frame!!So, here is an alternate parts list:For the drone itself:Flight controller: Happymodel ELRS X1 AIO with onboard 12A...

I would instead choose an SMA adapter and proper T or Moxon antenna combination like the following: - [Happymodel Moxon antenna](https://de.aliexpress.com/item/1005003690087542.html), the Moxon is directional. - [Happymodel Omni...

* 4 HOLE: fits 4-hole motors * 102 mm wheel base (was 98) --- There are a lot of versions now, so here's a quick tour of what you'll find here: **Pickle_65mm_trueX_V2 = X frame, from 5 to 6g (3hole, 4 hole, universal 9mm)** **Pickle_65mm_trueX_V1 = X...

I used a Happymodel EP1 antenna (longer one) to replace the original Airgain antenna and Improved the signal quite a bit (see picture for rssi dbm comparison with stock antenna). Any 2.4 GHz antenna with a ufl connector will do. You can also make...

NLR.STL uses the Happy Model Diamond F4 AIO https://www.racedayquads.com/collections/all-stacks-combos-aios/products/happymodel-diamondf4-aio-whoop-flight-controller-f4-fc-5a-1-2s-4in1-esc-25-200mw-vtx-choose-your-rx NLR_BF.STL uses the BetaFPV 1S...

Will probably be making some revisions to accommodate the HappyModel ES24TX Pro antenna (would probably work with other ELRS modules/antennas too but hard to say) in the not too distant future. Probably just going to be a small change to the part...

This is a strong and light Tiny Whoop style (25.5 x 25.5 mounting) canopy specifically deigned to accept:HDZero - Nano camera (also other 14mm nano style cameras)Happymodel - ELRS PP / EP2 receivers (the RX fits behind the camera on a tray - glue in...

The casing is meticulously crafted to snugly enclose a Happymodel GPS antenna powered by an M8n Ublox receiver that came with my Pixhawk clone. The casing consists of two primary components: the top and bottom parts, which are secured together with...

- There are two versions available, one optimized for BrotherHobby 0804 motors and another for HappyModel 0802 motors. ... The components I used to build this quad include: - Crazybee F4 Pro v2 flight controller...