happy meal logo 3d models

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

 I modeled some up but its the part I am least happy with.  I need to figure out a better/easier way to do it in Blender.  The original mesh is fairly fine anyway so I don't think a printer will do a nice version unless its a resin...

This was a fun, but challenging build for me, and I am pretty happy with the results, so I thought I would share in case others want to have a go. Below I have tried to cover most of the steps and some of the things I ran into while building this....

I was never 100% happy with my fan designs. Then I discovered 2 in 1 out hot ends. There are a lot of them that measure 18mm's X 30mm's. I have seen them described as MK8, J head, Cyclops, and Chimera. I believe Cyclops is 2 in 1 out and Chimera is...

Set many top and bottom layers and 100% infill to make sure.Print the lampshade frameI leave this to last because you need to be happy with your m=image sizes before printing the lampshade frame.Print a lampshade base, 4 x lampshade horizontals and 4...

but the label with time can slide, therefore the next step is important.Locking the containerThis step adds a security lock, so the label tag will not slide and the cover will for sure not open. My Workflow for drying seedsMy drying seeds...

Jan 18, 2022: beefed up the BLTouch cable tidy prongs, should not break as easily (hopefully) Jan 8, 2022: I was pointed out that the rigid mount for the dragonfly BMO could only take M2.5x6, So I added a version of the mount for M2.5x8, and maximum...

It went together easily, cools my parts, and I'm really happy with it.To Do:I'd like to try integrating the cable guide and fan mounting from Cable Guide for Ender 6 - BIQU H2 Extruder. That original thing doesn't fit with the adapter plate or...

The result is that the buttons match on screen to the soft buttons in my build and i'm happy with that, i'm going to take functionality over perfection as this was always a compromise design. ... ATTRIBUTION =========== My thanks and appreciation...

If you have used my 3D printed backplate then add the CentralgearSpacer over the central spindle of the  large Central_Gear.   Add the number wheelsMake sure the gears are aligned exactly as the image below.    The three number wheels are fixed to...

... stiff at first but should loosen up over time. A little big of silicon lubricant could also be used on the dovetail joints to make it work more smoothly.If you have any questions or problems with this design, I will be more than happy to help.

To provide enough wiggle to make the bearings happy, I tweaked the rods as noted above. We're talking about 0.10mm taken off the rod diameters maybe, not much. THE FOCUSING SHAFT:See the hardware section below for more info here (sizes and all...

Case for ESP32- and ESP8266-Boards, Raspberry Pi zero, Raspberry Pi pico, ESP32-CAM, different sensors and displays PDF-description --> https://cdn.thingiverse.com/assets/59/50/ab/a7/36/NodeMCU-Case.pdf I'm happy about every remix and make! ***...

There's a slight chamfer at the start of the pocket to assist in getting your firesteel rod to seat. I'm happy to upload the Fusion 360 raw file, but I'd like to first illicit feedback so there isn't a dozen remixes that confuse folks as to which one...

... most of the lines/blocks to explain the ideas behind them. As always, there is space for improvement and only your imagination is the limit</p> <h3><b>If you've made it this far, <u>THANK YOU</u> for reading and your interest. Happy printing!!!

If someone can figure this out, I would be happy to add the information. For the Duet, just open the config.g file and add the following commands anywhere above the M501 command: <b>; Filament Sensor config M591 D0 P2 C4 R20 S1 ; extruder...

Once happy, disconnect the USB cable and check that it works when powered via a 9v battery. Taping Ensure the device is not powered (unplug the USB connector and battery). Bend the LED pins and wires to one side.If using a cable tie, tie it...

... right and left) that slide over the tops of the frames, clicking in place. With your backdrop paper slid into the groove, just push each clip downward to clamp the paper in place. Just lift the clip to release the paper.Happy shooting!Sample Photos

I'm pretty happy with this and it wasn't super hard to accomplish. You can build a pure open top version like the original or a version with an enclosed cab. The topper is an add-on for either. The fender flares are optional and you can print...

It should fit nicely:Step 8: Finally use the already attached screws from step 6 to attach the “top ring upper”:Finisher step 9: Congratulations - you are done:Now find a nice place in your garden and mount tuck gauge onto a 12mm rod - I prefer using...

Also I am keen on seeing if anybody takes this technique and uses it on his or her own design (Please leave a note on the comments!).Design and Source CodeThe design has been implemented in OpenSCAD (the source code is provided for download).Happy...

Improvements: I'm not planning another version of this but if you feel like remixing it, the following suggestions come to mind as nice improvements: Not happy with the filament pegs for alignment, some more substantial grooves or clips would be...

... that is 2 pieces and hollow to save on plastic. 10/9/2022 - Narrowed the linear bearing seats and widened the rod through-holes on the slide top and bottoms (it seems to be rubbing when off-center pressure was applied) Happy flying! ...

The angle will depend a lot on your layer size, so make sure to check the print preview to make sure you're happy with it. The oval likes to print with some ringing (wherever the “top” of the oval is in orientation.) With resin prints, a healthy but...

and after a considerable number of try and error iterations and many test prints I am happy to share my new "OpenFLex universal terrain tile base and riser system". Instructions for FLexible bases ------------------------------- If you are...

... It went together easily, cools my parts, and I'm really happy with it. To Do: ------ I'd like to try integrating the cable guide and fan mounting from [Cable Guide for Ender 6 - BIQU H2 Extruder](https://www.thingiverse.com/thing:4907102).

Definitely not if you're happy with the current print quality. Personally, I really hate the eccentric nut adjustment, and also the wheels are fairly expensive compared to LM8UU or Drylin linear guides. At least in my case, when adjusting the...

... or equivalent which I found on Amazon US. I hope they will fit the boxes. In adition I'm not familiar with awgs of the wires and electric cables. I assume they will fit. Any questions please feel free to contact to me. Happy printing. ...

 I've also updated the gears print file.10/22/22 update: car body is available ! https://www.printables.com/model/298041-dodge-ram-rc-car-body-remix-----------------Well this was a long one and I'm happy to release it, finally !Please note that in...

Finally, happy tinkering! ... References ---------- Dual Z design inspired from https://www.thingiverse.com/thing:2334406 Hotbed carriage inspired from https://www.thingiverse.com/thing:2572598 Y tensioner, Y motor bracket,...