happy birthday 3d models

Set many top and bottom layers and 100% infill to make sure. Print the lampshade frame I leave this to last because you need to be happy with your m=image sizes before printing the lampshade frame. Print a lampshade base, 4 x lampshade horizontals...

I just wanted to be able to go back to stock if I wasn't happy with the experiment. So far, it's worked flawlessly. I've printed TPU, PLA, PLA+, and PETG without issue. Retraction settings need to be adjusted a bit depending on material and what...

I am so happy :D Update 16 (21.12.2018): I replaced the old "alternative" fan shroud with a new one. Also replaced the old "3 Point Leveling Package". The new one includes a new z stop mount. Print Settings Printer: ANET A8 Resolution: 0.2 Infill:...

... contributions from the community. All the best for 2022 and may all your prints stick :PHappy printing and stay tuned :DYours KERLE MAKERSPACEPS: Feedback is especially welcome on this project.Assembly instructions and more info are provided as pdf

I'm not happy with this fudge, as I expect there could be situations in which it doesn't work. As a future TODO, I think I'd like to include a parameter which indicates where the reference vector should try to point at each path point (e.g. for a...

Happy viewing! Bill of MaterialsItemAmountCommentAluminium rods ⌀12 mm x 1m4Same as you used for HadleyWooden disks ⌀45 cm2I had them made out of 9mm plywoodVinyl record1I got it for cheap at a thrift shopTeflon furniture pads3 M8 bolt 40mm1This...

Now I'm off to trip the light fantastic!Ta-ta and happy printing.Update for Filament Labels As Shown in Last Picture.I've just created a filament tag system for my filament storage boxes. Full details of that design are...

10) Once you are happy with the box operation. Press the optional 'Screw Covers' in place (I don't recommend gluing them, otherwise you cannot dissassemble the box fully and you may glue the rotating screw joints) to hide the screws. You can also...

If you print and use it, please be so kind to post a picture. Happy printing and stay safe everyone! Print instructionsThis is what you need to do get it printed and assembled: Print the axis and the spring washer at 100% infill and with a small...

... and the case bracket prints on its side.  Further ThoughtsYou can of course combine as many strut parts as you feel comfortable assembling into a teetering exercise in balance :D Happy printing!xoxoSven. ---525 Rpi5 Multiscreen Assembly

I designed this because I wasn't very happy/impressed with the other mods out there. I will be doing diagrams and more detailed instructions for assembly eventually, but I want people to try this mod and provide feedback before I do that. So please...

BigTreeTech Mini 12864 RGB LCD enclosureI am very happy to present you a versatile simple enclosure for the LCD screen => BigTreeTech Mini 12864 RGB.The purpose of the design is:to have a case without visible screws on the front face.to have...

... https://github.com/kevinakasam/KlackEnder-Probe Drop a comment with any questions or issues, and I'll do my best to help or adjust the design. I did this at least once, so I'm officially an expert now :) Good Luck and Happy Printing!!

... or equivalent which I found on Amazon US. I hope they will fit the boxes. In adition I'm not familiar with awgs of the wires and electric cables. I assume they will fit. Any questions please feel free to contact to me. Happy printing. ...

After printing a custom Stratocaster that I found, I decided I wanted to try making my own guitar and since there wasn't a bass available to download, I figured I'd give a try at making that.Here is a list of all the parts I used to build the bass...

If you are happy with the test fit of 2 out of the 4 bolts, then you can go ahead and mark / drill the 2 bottom holes through the A-Pillar Gauge Pod Adapter. I had to put them low enough to allow room for my radio there. If you are using a...

Scroll down! Happy printingMFGChrisFollow me on...  prusaprinters.org  thingiverse.comInstagram @schiffer_softIf you like it ;) - Thx for me!www.paypal.me/schiffersoft How to print it? Step 1. prepare the...

I was not happy with the bearing since it resulted in wobble of the Hubs if it were placed in a larger hole. I designed the Bearing Extended to take care of this problem and have been using it for a couple days. I have experienced a few problems...

I would be happy to hear any reports on this. The assembly remains the same, only the hard rings are pushed on from the middle before screwing. Please pay attention to the direction. ______________________________________________________!!! This...

(BTW: The R3 component is 5k in size :-) ) Console Tasmota: rule1 ON Power2#state=1 DO Power1 1 ENDON ON Power3#state=1 DO Power1 1 ENDON Rule2 ON Power1#state=0 DO Backlog Power2 0; Power3 0 ENDON ON Power2#state=0 DO Backlog Power1 0; Power3 0...

--- Parts list 132cm radiator --- 1x ModulsRight_132cm_Radiator Controller.stl 4x Moduls_2x.stl 1x Module_1x.stl 1x ModulLeft.stl 2x Molex4xAdapter Male 3Pin.stl 8x 8cm PC fan (3pin Molex) 34x 10x3 round neodym magnets 1x Temperature controller...

If assistance is ever required relating conversion between these various formats provided by your renderer – simply don't hesitate to reach out team of experts here today who'd be happy help answer any additional inquiries about rendering and export...

Very happy with this board. It is using the same chip (TPA3116D2) as the amplifier I used in V2.0 but has a better designed board, no noise, it has treble and bass control, and great sound. All details at: <a...

Ultimately, I used Loft/Boundary bosses (profiles + guide curves), which gave me a result I'm happy with. I made two fully defined master 3D sketches, one for each lever, assigning them reasonable dimensions (increments of 0.25 mm) to closely match...

Pretty happy about this little proof of concept P.S. print without a brim or even a skirt, since the second layer (and on) will cover those lines partly. Or do like I did (when I realized what was happening just in time :)); swiftly peel the skirt...

The 5W lamps are the wrong ones :PIf the bracket for screwing the instrument cluster to the dashboard is also gone, I added an adapter plate ("Adapterplatte") to the files.Printing instructions:Material: ABSInfill: 100%Brim: YesSupport: EverywhereThe...

(120$ open box ) I am really happy with the performance of this build, I had zero dollars for budget on this build, I literally used spare parts are already had in my garage. The router was free (from harbor frieight credit points) you can...

Remember that it may need some variation or modification and I would be happy to hear them to implement it. ####################################################################### This model of stabilizer bars for the Z axis has a fairly strong...

With a happy grin insert some gifting money and imagine how much joy they will have when they extract your generous present and forgets the frustration and remember it as fun. If you like this thing, please leave a nice comment to help with my...

A wall mount for spools that use the bearings and aluminum tubes from the MMU tray it replaced. I came up with this Wall Mount for Prusa Multiple Materials 2S Filament Buffer solution because I couldn't fit five Prusa Trays on my desk behind the...