happy birthday papi 3d models

Depending where you solder the wire from microswitch you have to change board.GP{number of GPIO}.Preflight check Go to Control Panel → Devices and Printers →  Right click Pico → Game controller settings → CircuitPython HID PropertiesHere...

I hope this proves helpful and happy printing! Once again, feel free to reach out with any questions. Links and Cost Analysis 3/8" Wooden Dowel: $1.29 ea https://www.homedepot.com/p/3-8-in-x-48-in-Raw-Wood-Round-Dowel-HDDH3848/204354371 ...

All right reserved // web: http://www.RinkyDinkElectronics.com/ // // A quick demo of how to use my DS3231-library to // quickly send time and date information over a serial link // // To use the hardware I2C (TWI) interface of the Arduino you must...

It took some tuning & fiddling with settings but eventually I was quite happy with it. However I wanted a bigger build volume, and if possible some additional stability. I didnt upgrade the z axis, only x and y - might do that later but for the time...

... halves together using super glue on the rim of the bottom. Wait for the super glue to dry according to its instructions. Congratulations, you are done! As this is my first post here any feedback is appreciated. Happy printing from Munich, Germany!

That being said, I was not happy with the offerings on Thingiverse/Prusaprints, and decided to make my own, in a style that is more than just a straight pipe with charcoal pellets. This style should minimize the the footprint while increasing the...

... no legal rights to it. Enjoy. This model has an extreme focus on both inside and outside detail, not like others. Please Take Full advantage of that.-JHUPDATE: Happy 100 Downloads! ...As customary, there is a redesign completed.Thank you all!-JH

Right-click the casing/core and select “SPLIT TO  PARTS” then right-click the core and select “INFILL”  and set infill to 100% for the CorePost print instruction:The Casing top-surface that rotate against the Lid might need some light...

Good morning, folks! An assembly video is available here: https://www.youtube.com/watch?v=gMeAFoPIWX0 I'm super happy to present you my latest design. I took advantage of this quarantine period to learn a bit more about programming, and I set up...

 Happy printing! Printing Suggestions- I would print this in at least PETG- 4 perimeters, first layer height of 0.2mm and layer height of 0.15mm- 20% infill with the Gyroid fill pattern- I would use Organic supports (with "For support enforcers only"...

fireproof pad, cut-resistant gloves....) I hope you like my model and I would be very happy if you share and like!!! ;) Please take a look at my other models! Sie machen alles auf eigene Gefahr! Beachten sie das man schnell mit dem Messer oder...

Intro Media Control Knob inspired by Mikolas Zuza design: https://blog.prusaprinters.org/3d-print-an-oversized-media-control-volume-knob-arduino-basics/ I've changed the enclosure, code and used digispark instead of arduino so it's hard to call it a...

A wall mount for spools that use the bearings and aluminum tubes from the MMU tray it replaced. I came up with this Wall Mount for Prusa Multiple Materials 2S Filament Buffer solution because I couldn't fit five Prusa Trays on my desk behind the...

 The FreeCAD one is a bit nicer, but the OpenSCAD one is fully parametric in a friendlier fashion.Anyway, I'm very happy with these, and hope they are useful or inspiring to someone else. OpenSCAD ParametersThe OpenSCAD version is fully...

I was not happy with the bearing since it resulted in wobble of the Hubs if it were placed in a larger hole. I designed the Bearing Extended to take care of this problem and have been using it for a couple days. I have experienced a few problems...

When you're happy with your route, glue the LEDs in and the light beads. When they've dried, glue the lens in like you did with the first letter - Don't forget to clamp! Now follow the same system for the second letter "L", clamping again till...

Very happy with this board. It is using the same chip (TPA3116D2) as the amplifier I used in V2.0 but has a much better designed board, no noise, it has treble and bass control, and great sound. PRINTING. This should be a simple print. You will...

It seems to be something from a bit ‘back in the day’, ie they were once common but as printers have gotten better, they're less required, again I just wanted to experiment and was very happy with the quality increase I saw in my prints so i've...

... that the base part still fits. While the top part is facing down, add super glue to it's inner rim and glue the base part in place.Optional: Add rubber feet stickers. Any feedback is appreciated. Happy printing from Munich, Germany!

In Cura this can be found under: Extensions > Post Processing > Modify G-Code > Add a script Finishing with glitter You will need: Water-based découpage glue - clear gloss works best A fine brush - one you are happy to use to apply the glue Glitter -...

It would be possible to design a "lens donut" if needed, but I'm already very happy with the current design. Print InstructionsI printed the rod support, the core of the matte box, the mini hood, and the fastener with the beautiful and sturdy...

Here are more of my anatomical designs you might enjoy: Novelty: Wearable Spine: https://www.thingiverse.com/thing:4982223 Skull Jewelry Set: https://www.thingiverse.com/thing:4980129 Happy Halloween Spine: https://www.thingiverse.com/thing:4979522...

>1\_120\_-\_boxcar_TTm\_V08\_Seat\_inlay\_practical.stl >>a seat inlay with shorter pimples, depending on the first layer it could be easier to fit this into the roof, even the other is okay in my opinion 2022-10-08 V08 (looks like a working release...

Here are the final files: texture on cane holder v3.stl clamp protector tri.stl screw.stl Here are alternative files: alt screw updates.stl (useful if user has grip difficulty) cane holder clamp latch texture v1.stl (design is WIP) Recommended...

I strongly advise dry-fitting everything to be sure you are happy with how things go together BEFORE attacking it with a soldering iron!!! PS Chances are you ended up with more parts than you need as well as more than one PCB. That's ok, it's nice...

For adjusting the scale of your helmet simply multiply the measurement you are attempting to adjust by desired percentage until you get it scaled down to a measurement you are happy with. **See example below.** On another note, always check more...

The vinyl went on pretty well and we were happy with it. I've added a picture of the finished model with this post. A parachute was added and the rocket is now ready to fly. Hoping to go flying in the near future, but the weather will be a big...

And yes - I don´t like hex...

To provide enough wiggle to make the bearings happy, I tweaked the rods as noted above. We're talking about 0.10mm taken off the rod diameters maybe, not much. THE FOCUSING SHAFT:See the hardware section below for more info here (sizes and all...

There's a slight chamfer at the start of the pocket to assist in getting your firesteel rod to seat. I'm happy to upload the Fusion 360 raw file, but I'd like to first illicit feedback so there isn't a dozen remixes that confuse folks as to which one...