hangers for ornaments 3d models

I loved Kelly Egan's spiral ornament (https://www.thingiverse.com/thing:210741) and wanted to make it easier to add a ribbon or thread for hanging, so I created a "loop" attachment. ...The original hole remains intact, providing a backup option in case...

Wanted an Ornament bracket so I could hang the Razor Crest. ... Printed at 20% infill, and used a raft for adhesion, but didn't need any supports (Angle isn't sever enoug

I call this ode to charlie brown, one tiny little tree, and one hanging ornament :P Here is a holder for my Christmas Gyros, the two halves slide together and the ornament will fit onto the post (the holes for the gyro's may need light sanding and...

but it leaves a neat round hole, and the resulting ornament is hollow. This print is the hanger for printing Jakobs Christmas Ornament in vase mode. Very short print time, and you just squeeze the loop to slip the hanger into the hole in the...

Hangers for Thule Shoe Organizer

CONNECTOR FOR HANGERS, 4MM THICK

3d print-ready cat hangers for baby clothes.

Tiny tots' garments require compact hooks that keep them secure and within easy reach, perfect for little ones who can't quite grasp regular-sized hangers on their own. ...And let's not forget about oversized dolls that need a dedicated spot to hang...

Holder for clothes hanger. Can be fasten to wall or to shelf. ...Holder is design for wood stick 12 mm.https://www.facebook.com/3DTisk-Ku%C5%99im-292458122565015

It is especially useful for suit trousers that are quite thin and not very stiff. Printing instructions:Print lying flat with 5-20% infill for best results. ...They take about 45 mins each.I would recommend increasing the perimeters to 3 or 4...

Twist on hangers for the greenhouse. To put strings through, or just to hang things on.There are three variants included.As the temperature can be high in the green house, PETG is to prefer.Printed in an 45° angle as in the picture, supports...

Radiator hangers are simple to install and remove. ...They fit easily onto the radiator.

Hanger holder sketched out hastily, currently being tested. ...So far so good.

Radiator Hangers that snap into place are convenient to use. ...They can be easily fitted or removed as needed.

I've designed a simple drill hanger specifically for my budget-friendly Guild drill. Contents: The front holder measures 8mm wide and features a 42 mm semi-circular gap to accommodate the chuck of the drill, along with a small vertical wall to...

This is a simple hook that clips onto wire hangers that allow you to store things like hats/bags or anything you can think of.

This wall hooks can put at least 5 clothes hanger on it. I install it on the back of my bedroom door. Category: Organization

This wall hooks can put at least 5 clothes hanger on it.I install it on the back of my bedroom door.Category: Organizationupdate note: 2022/06/05 It has been lengthened by two centimeters, the end has a raised shape, and the hanger at the end is not...

This small hook adapts to more or less any type of hanger, and allows to optimize the storage by superimposing several hangers. ... Of course the model can be optimized in size and quantity of filament used, but it is simple and efficient, easy to...

An aditional folding suport for your wardrobe

Space-saving hook for your cabinets

Dimensions for a Single Binder: 20 millimeters by 30 millimeters by 23.5 millimeters A hole diameter of six millimeters. ... Dimensions for a Double Binder: 20 millimeters by 44 millimeters by 23.5 millimeters A hole diameter of six millimeters.

DIMENSIONS for single binder: 20mm x 30mm x 23.50mm hole diameter 6mm DIMENSIONS for Double binder: 20mm x 44mm x 23.50mm hole diameter 6mm ------------------------------ These dimensions will come in handy when I become my wife's personal shopper.

One of my initial prototypes for a three-dimensional printing device might prove useful to someone someday. ...I created it using the software application TinkerCad.

I've got a few workarounds for IKEA Skadis to stabilize that Thingiverse pen holder at https://www.thingiverse.com/thing:3273957

I've crafted a custom holder for filament spools to perfectly match the 1 1/2 by 3/4 inch wood Joel has chosen for his filament storage shelves. ...The holder consists of two seamless halves that join together effortlessly, forming an incredibly sturdy...

Dimensions for single binder: - Length: 20mm - Width: 30mm - Height: 23.50mm - Hole diameter: 6mm Dimensions for double binder: - Length: 20mm - Width: 44mm - Height: 23.50mm - Hole diameter: 6mm This design is ideal for a salesperson or personal...

... this to space out wire hooked hangers on 8mm rods. ...She loved it and then asked for an updated version for a larger gap between hangers for sweaters - that's the double. I printed without supports using PLA. ...No overhangs over 45 degrees.</p>

hanging system for clothes hangers this bracket is designed for a tube around 12.5 mm

To shim the gap for use with thinner doors. ...15 and 20mm thick versions included, simply slide onto hanger to fit. ...