hand cranked drill 3d models

A hand cranked drill with changeable tool. The gear ratio from the crank to the tool is about 1 : 3.5 . All parts are 3d pinted except drill bit. Also some glue is required for assembly. ...With the files is also an instruction picture.

this is a old typical mancuna hand- cranked drill. model have a old rusty look. the model is created in autodesk maya and and textured and rendered in substance painter. the whole prosses of this asset done with gaming pipe line baking done in 2k...

Screws (I used what I had on hand, mostly M2 and M3)Spring or elastic band (The stronger the spring, the stronger the drill but it makes it harder to pull. Experimenting is key. ...I don't have a particular model to recommend as I modified a spring I...

Screws (I used what I had on hand, mostly M2 and M3) Spring or elastic band (The stronger the spring, the stronger the drill but it makes it harder to pull. Experimenting is key. I don't have a particular model to recommend as I modified a spring I...

Use one hand to hold and push the drill in, while your other hand cranks the drill bit around and around. Easy! This is a mashup of two clever designs.Hand beater handle, https://www.thingiverse.com/thing:4290265andHandle for 1/4 inch hex...

Use one hand to hold and push the drill in, while your other hand cranks the drill bit around and around. Easy! This is a mashup of two clever designs.Hand beater handle, https://www.thingiverse.com/thing:4290265andHandle for 1/4 inch hex...

... to be glued together in some cases - think about it before you start assembling this thing. You can position the crankset on either side, making this a versatile toy that's perfect for left-handed or right-handed folks alike. ...Have fun with it!

This is an adapter to use a drill instead of the hand crank to raise and lower the wooden top of a husky tool box. I used an old dull drill bit (broke off the bit) that had a quick drill adapter –– so it fits in my quick release chuck adapter. ...You...

Cranking handle with movable knob for old polish handdrill PWWe10.Inside diameter 11mmInfill 20 %Printed with PLAYou will need bolts:1x - M3x201x - M3x10

A CAD depiction of a hand-operated drill press, fashioned after an actual unit, was created by me without disassembling it. ...Certain internal measurements and operations had to be approximated due to limited access.

Head can be used with the detachable hand crank or attached to any standard hex bit for use with a power drill. Print in orientation shown in picture for maximum strength (though will print vertically oriented if your printer struggles with holes in...

I used a 1" wood screw to assemble, along with an old drill bit that I cut the head off of with a hacksaw.

I designed a basic tray with a hole tailored to convert the "Hand Cranked Vinyl Player" into a manual turntable, allowing me to capture rotating 3D models on film. Mesh density: 10% Print settings: No support material needed. ... Thanks!

This is the Hand-Cranked flashlight from my latest YouTube video: https://www.youtube.com/watch?v=Ry8VIKx3lno It uses a 28BYJ-48 Stepper Motor: https://amzn.to/408IMCR Bill of materials can be found here:...

This is a printable hand-cranked record player specifically designed for vinyl discs. Every piece of this record player has been neatly aligned and crafted to fit inside a 15x15x15cm cube, printing perfectly on the Replicator 2 without any rafting or...

This is a printable hand-cranked record player designed specifically for vinyl discs. All components of this record player are carefully aligned and crafted to fit snugly within a 15x15x15cm cube, printing flawlessly on the Replicator 2 without any...

A 3D-printable, hand-cranked generator has been created to inspire kids to think creatively about what is possible. This design revolves around a 12-volt DC motor from a window flusher fluid pump and features gearing approximately 1:29.16. The...

A hand-operated compost grinder is an efficient tool for breaking down organic waste into fine particles, making it easier to incorporate into soil or garden beds. ...This device requires no electricity and can be easily operated by turning a handle,...

Hand-cranked sharpener modeled in Blender, with a cycles preview image. The .blend files include all scenes and have poly counts prior to subdivision. Perfect for close-up renders, and the parts/materials are logically named. ...Additionally, you can...

To replace that mechanism I extended the "plumbing" piece that it attached to, and made it run all the way through the hand crank and the crank gear. This allowed a screw to be used in the plumbing along with a washer. 5. Washer have also been...

Replacement Crank for Small Hand-Cranked LED Flashlight This replacement crank is designed to fit a commonly used small hand-cranked LED flashlight, as shown in the accompanying pictures. I have purchased several of these flashlights at a cost of...

This is a replacement part designed specifically for a small handheld LED flashlight that relies on manual cranking (refer to images provided).\nI have purchased numerous of these flashlights at affordable prices, under €2 each, but unfortunately,...

Thingiverse member jsturm requested a clockwise cranked version of the Marblevator Mini, Hand Cranked Base, so here it is, featuring more parts than the original with a handle that cranks clockwise instead of counterclockwise. ... A video showcasing...

Thingiverse member jsturm requested a clockwise cranked version of the Marblevator Mini, Hand Cranked Base, and here it is. This revised design includes more parts than the original and features a handle that cranks clockwise instead of...

I recently printed the Hand Cranked Heart gear, available on Thingiverse at http://www.thingiverse.com/thing:253934 and http://www.thingiverse.com/thing:243278. However, I experienced a problem with the large gear skipping due to excessive space...

... spin on the classic ripple effect. ...Check out this video prototype to see how it works: https://www.youtube.com/watch?v=vYGLG5_vWZQ. Special thanks go to Thingiverse member alexlfarlow for suggesting a hand-cranked version - and here it is!

I recently manufactured the Hand Cranked Heart gear, specifically the models found at thingiverse.com, numbers 253934 and 243278. However, upon assembly, the large gear was prone to skipping due to excessive space above it. ...To resolve this issue, I...

This is a counter-clockwise hand-cranked base designed to work with the three Marblevator "Mini" tracks: Bowl, Seesaw and Zigzag. For a clockwise cranked version, see this thing: http://www.thingiverse.com/thing:313944. The photo shows the...

I experienced issues when printing the Hand Cranked Heart gear from Thingiverse (http://www.thingiverse.com/thing:253934 and http://www.thingiverse.com/thing:243278) because of excess space above the large gear. The problem was resolved by adding a...

First of all, this is just a quick and dirty solution (the problem is simple, I'm too lazy to crank it by hand every morning), I will definitely upgrade it (making a motor housing to be quieter, hiding electronics), but using it with a drill was...