hackrf portapack h2 3d models

#Parts * HackRF+Portapack H2+battery (clone):https://s.click.aliexpress.com/e/_dSMPvNo Screws (M2.8x10mm and M2.8x8mm):https://s.click.aliexpress.com/e/_dSS6UAQ [optional] 3d printing pen (to fill the led holes with translucent...

#Parts * **HackRF+Portapack H2+battery** (clone): https://s.click.aliexpress.com/e/_dSMPvNo * Screws (M2.8x10mm and M2.8x8mm): https://s.click.aliexpress.com/e/_dSS6UAQ * [optional] 3D printing pen (to fill the LED holes with translucent material):...

They are an improvement over the original files: 1) less tight fitting 2) better sd card slot 3) bigger holes for reset and dfu button 4) better fit, specially on the 2 bottom SMA Parts *HackRF+Portapack H2+battery (clone):...

Lower profile knob for Portapack H2. ...Should fit snug.

Here is a stand for the Portapack that doesn't block access to the charging and audio connectors on the bottom, and doesn't obscure the writing on the front.I printed with 15% infill, skirt but no brim. Supports are required.Please note, this will...

Hackrf portapack h2 h1 wall mount holder. ...I will add a flat to wall in ver2

This is an elementary exercise for the HackRF One PortaPack H2.

Just another portapack H2 standPRINT WITH SUPPORTS

A simple stand to hold my HackRF with Portapack H2 that I designed in about 5 minutes with FreeCAD. (FreeCAD file included) It has a hole in the back for the wires. ... Nothing fancy, it just gets the job done.

The HackRF one + Portapack H2+ is compact in size, but it is lack of button cover. I tried the other on Thingiverse, which does not fit. ... So, if the other one does not work for you, there it is.

Here is a rewritten version of the original text: The HackRF One and PortaPack H2 are now available as a downloadable 3D printing model, allowing users to create their own custom cases.

This cover shields your Portapack H2 screen and buttons. Tailored for the case I designed, it's easy to set up: just print and attach the magnets in place - make sure they stick out slightly. The revised version is the white one shown in the photos....

This cover protects the screen and the buttons of your Portapack H2. Designed for the case I made. Just print and glue the magnets in place. They should protude slightly.</p> <p>The revisited version is the white one from the photos. ...Since is flat,...

Hello everyone,Introducing the remix version of https://www.thingiverse.com/thing:4260973. ...I believe a speaker should be free from its enclosure, so I've created a speaker holder and stand, along with a couple of additional holes in the original...

A tad smaller knob than the one that came on my Portapack H2+ HackRF One. I printed this in "clear" filament to better view the 4 blue battery status LEDs. ... SCAD file attached in case dimension changes are desired.

Tilt stand for Portapack H2+ HackRF with cutout for speaker and cable routing, with stylus holder. Check case dimensions before printing to ensure correct fit (default opening size is 88mm width x 29.5mm depth with a 3.8mm corner radius). Default...

A stand for a HackRf portapack H2 with a small folded horn for the speaker! cutout for cables. ...

A slip-on cover to protect the screen & keep from pressing buttons on Portapack H2+ HackRF when in storage or in luggage. Designed to fit Portapack H2+ in an aluminum case, also featuring a slot on the right side to store an extendable (detached)...

Some of us may think the buttons stick up too high on our Portapack H2 or H2+, fearing they might get broken off. WELL, do I have a solution for you! Glue this little gizmo to the case around the buttons, and voila!, the buttons no longer seem to...

This HackRF case will provide a full SMA protection and support for PortaPack, battery and 50mm flat speaker Print it with 0,4mm nozzle. extrusion width 0.35. layer height 0.2, 3 layers, 30% infill You will need at least a 10mm brim!!!! ... Remixed...

Lets make our HackRF Portapack H2 comfortable. ...This is just a crade for your HackRF Portapack H2

Stand for the HackRF Portapack. This design leaves room for connecting microUSB and headphones on the bottom of the HackRF. Secure the HackRF using either a zip-tie, velco tape, or some type of strap. ...

Hi,A stand for your HackRF portapack.The STL is wrongly oriented.You can print it standing up on it's legs

The enclosure I've created is specifically designed to fit the HackRF One Portapack, carefully ordered from Rysc Corp. ...By leaving a space in the STL file, it's made simple to add your own unique callsign at any time.

It fills in the gaps left after installing the Portapack atop your HackRF one, ensuring a smooth and secure setup. The latest version 3 of this skin has rectified the hole placement issue and introduced tabs to securely support the top of the skin...

The is a stand for the Hackrf PortaPack. V2 had too little space for a nice cable radius, but might be useful if you want to remix it V3 has a sarcastic text V4 has a wider foot Mind printed on my Dagoma Neva in around 4 hours. I use 33%...

Stand for HackRF with a Banggood PortaPack. There is a cutout in the back for Usb/coax cables to exit (I was just a bit sloppy with my photo). ... I tried to make it tall enough to accommodate cables coming out the bottom.

==================================================================== Update 26 September 2021: I posted an improved design with a different loudspeaker: https://www.thingiverse.com/thing:4975411...

Simple cover to the Portapack for the HackRfOne

I utilized a versatile stand to create a mobile police scanner utilizing my HackRF and a circular USB battery pack. ...A Raspberry Pi attaches to the rear, delivering swift decoding capabilities.