gtech multi plus 3d models
124008 3d models found related to gtech multi plus.
thingiverse
If you use your Gtech multi handheld vacuum cleaner to suck up spiders or other nasty creepy crawlies, the last thing you want is for them to creep back out later. ... This simple plug will make sure they stay trapped inside the Multi
thingiverse
The faulty fan blades on my GTech Multi ATF001 cracked and chipped, causing the motor to run loudly and vibrate excessively.\r\nThis replacement fan blade will seamlessly fit in place of the original, restoring smooth operation to the Multi.\r\nTo...
thingiverse
The Gtech Multi MK1 Floor tube accessory has a design flaw. Any slight pressure on the tube will snap it where the aluminium tube meets the black plastic tube at the top. I went through 3 of these tubes before realising there was a design flaw and...
thingiverse
A small diameter nozzle that fits into the Gtech Multi hand vacuum cleaner. You can also insert a standard drinking straw into the nozzle to get to hard-to-reach places. Useful for cleaning out computer keyboards etc. ...
thingiverse
Wall Mount for Gtech MK (K9) Tools. ...The Extras Holder Attaches to the Car Kit at the Bottom.
myminifactory
Gtech AirRam Wheel2 part design for a Gtech AirRam wheel makes it easy to print and saves on support material. Two parts are also possible, matching the original colors exactly is achievable. My grey matches perfectly but I need to reprint the green...
thingiverse
If you are tall like me the long nozzle for the Gtech just does not reach the ground when stood straight up. ... I designed this 145mm extension to fit onto the Gtech nozzle and then hold the long nozzle in the other end. ...No stooping required.
myminifactory
... a new wheel and cap for it. ...The cap is very simple but works perfectly - a wheel will follow. Due to the raised parts, it's best to print with PET as PLA might snap. Part for Gtech AirRAM Series: DM001 Model: AR02 Serial Number: 11940-008076
thingiverse
Replacement Wheel for GTech AirRam Vacuum Cleaner. After witnessing the second catastrophic failure, where the other half managed to smash a wheel off the vacuum cleaner, it became clear that ordering replacement wheels was no longer the most...
prusaprinters
Wall mount for the Gtech MK (K9) Tools. Holds the extras for the car kit at the bottom. Print instructionsCategory: Organization Print Settings Printer: Qidi X One2 Rafts: No Supports: No Resolution: 1.6 Infill: 30% Filament: Any PLA Any
thingiverse
For a GTech hand held 22 Volts My uncle's careless mistake resulted in a corrosive substance spilling onto the vacuum's service area, causing severe damage to the bottom and fusing the battery to the base. Uncomfortable with the appearance of the...
thingiverse
I have a Gtech Airam but the wheel fell off. So here is a widet that replaces the broken tabs on the wheel. It is a tight enough fit that I have not used glue, but that may change if it fails in heavy use. For fun I've added a picture of how the...
thingiverse
Bracket / clip to keep your Gtech Pro2 fixed to the wall instead of sliding / falling down.... Using PLA with 25% infill keeps it flexible enough for easy use. No supports necessary. ... The clip is based on parametric clip by henpenben using...
thingiverse
replacement part for SEB Multi Robot Plus Type 8590. ...
thingiverse
Customized version of https://www.thingiverse.com/thing:1571860 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1571860
thingiverse
Customized version of https://www.thingiverse.com/thing:1571860 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1571860
thingiverse
Customized version of https://www.thingiverse.com/thing:1571860 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1571860
thingiverse
Multi Device Charging Station Details A station designed for multiple device charging with an integrated pencil/pen holder. ...Print Settings Printer Brand: MakerBot Printer Model: MakerBot Replicator 2 Raft Requirements: None needed Supports: Yes...
thingiverse
Y-Plate replacements for the Wanhao Duplicator I3 Plus are available. Measure carefully the center-to-center distance of your Y-Shafts and verify that you use the correct file for your printer model. The provided file will work perfectly with both 3...
thingiverse
Gtech AirRam Hanging Bracket Important: I found these work well, but leave marks on the Gtech. These brackets are designed to hang a GTech AirRam Mk2 from a wall. 3D Print long side left to right as shown in the Cura Pictures above. Video: Gtech...
myminifactory
Gtech AirRam Hanging Bracket I found these work well but they leave marks on the Gtech. These are designed to hang a GTech AirRam Mk2 from a wall. 3D Print long side left to right as shown in the Cura Pictures above. Video: GTech AirRam Wall Bracket...
thingiverse
If you own a Gtech Pro vaccuum cleaner then at some point you will need some of these clips because the original items break easily and do not seem to be available as spares. ...
prusaprinters
Gtech AirRam Hanging bracket IMPORTANT I found these work well BUT leave marks on the Gtech These are to hang a GTech AirRam Mk2 from a wall. 3D Print long side left to right as shown in the Cura Pictures above. Video GTech AirRam Wall Bracket...
thingiverse
I successfully snapped one of the cable management clips attached to the motor on my Gtech e-Bike's power cable. Upon reviewing the bike's specs, I recall that the 5mm diameter cable utilizes an M4 bolt for secure attachment - a design that may also...
myminifactory
... with PET material and 100% infill for added stability, supports were also enabled for the locking tabs to ensure perfect functionality. This part is specifically designed for the Gtech AirRAM Series DM001 Model AR02 with Serial Number 11940-008076.
thingiverse
A Replacement Blade for the G-Tech Cordless Strimmer. ...You Can Create Your Own for Under Four Pounds, a Price That Makes This More of a Challenge Than a Necessity.